• Practice
  • About 24 min
  • 5 practice questions

Surface tension, angle of contact, excess pressure and capillarity

Explain surface tension from intermolecular forces, relate it to surface energy, list what changes it, and use the angle of contact, excess pressure 2T/R and 4T/R, and capillary rise h = 2T cos θ/rρg.

If something looks wrong, please tell us.

By the end of this lesson you can

  • Explain cohesive and adhesive forces and why surface molecules have extra energy.
  • Define surface tension and surface energy and show they are numerically equal.
  • List the factors that change surface tension.
  • Explain the angle of contact and derive the excess pressure inside drops and bubbles.
  • Derive and use the capillary rise formula.

Water striders walk on ponds, paint-brush hairs cling together when lifted out of water, and a greased needle can float on water although steel is about eight times denser. Water and kerosene do not mix; water wets glass but mercury does not. All these come from the forces between molecules at a liquid's free surface.

Intermolecular forces and the free surface

The attraction between like molecules that holds a liquid together is the cohesive force; the attraction between molecules of a liquid and a solid it touches is the adhesive force. These forces act only over very short distances, about 10⁻⁹ m; the sphere within which a molecule feels them is its sphere of influence. A molecule A deep inside the liquid is pulled equally in all directions, so the net force on it is zero. A molecule B near the surface has more liquid below than above, so it is pulled downwards. A molecule C right at the surface feels the largest downward pull. Bringing a molecule from the interior to the surface needs work against cohesion, so surface molecules have extra potential energy. A system is stable when its energy is least, so a liquid tends to have as few molecules at its surface as possible: its surface tends to contract to the least area. This is the origin of surface tension; the surface behaves like a stretched elastic membrane.

Examples. A water strider's weight is supported by the stretched surface. Brush hairs cling together because the water film around them contracts. A floating needle sits in a small dent of the surface; the surface-tension forces along the dent are slanted, and their vertical parts hold up its weight (add soap and it sinks). A camphor boat moves forward because camphor dissolving at its back lowers the surface tension there, so the stronger pull in front draws it along.

Surface tension and surface energy

Surface tension T is the force per unit length acting along the surface, at right angles to any line drawn in it: T = F/l. Its SI unit is N m⁻¹ and its dimensions are [MT⁻²]. Surface energy is the work done per unit increase in surface area: W/ΔA, in J m⁻² (which equals N m⁻¹).

They are equal. A soap film on a wire frame ABCD has a movable wire AB of length l. The film has two surfaces, so it pulls AB inwards with F = 2Tl. Pulling AB out slowly by Δx needs work W = 2Tl Δx, and the area of film increases by ΔA = 2l Δx (both surfaces). Surface energy = W/ΔA = 2Tl Δx/2l Δx = T. So surface energy per unit area is numerically equal to surface tension. Remember: a liquid drop has one free surface (area 4πr²) but a soap bubble has two (area 2 × 4πr²).

Worked example 1: work on a soap film and a bubble

Take T = 0.030 N m⁻¹ for soap solution. (a) On a frame, a wire 5.0 cm long is pulled out 2.0 cm. ΔA = 2 × 0.050 × 0.020 = 2.0 × 10⁻³ m², so W = TΔA = 0.030 × 2.0 × 10⁻³ = 6.0 × 10⁻⁵ J. (b) Blowing a soap bubble of radius 1.0 cm creates area 2 × 4π × (0.010)² = 8π × 10⁻⁴ = 2.51 × 10⁻³ m², so W = 0.030 × 2.51 × 10⁻³ = 7.5 × 10⁻⁵ J.

What changes surface tension

  • Contamination and impurities change it, depending on how much is present.
  • Dissolved substances: a highly soluble substance such as common salt (NaCl) raises the surface tension of water; sparingly soluble substances such as soap or phenol lower it.
  • Electrification lowers it, because the electric force tends to spread the surface out.
  • Temperature: surface tension falls almost linearly as temperature rises. Over a small range T_t = T₀(1 − αt), where T₀ is the value at 0 °C and α the temperature coefficient. At the critical temperature (374 °C for water) the liquid-vapour boundary disappears and the surface tension becomes zero; van der Waals' relation T_t = T₀(1 − t/t_c)ⁿ, with temperatures on the kelvin scale, describes this more accurately.

Angle of contact

Where a liquid surface meets a solid, it curves. The angle of contact θ is the angle between the tangent to the liquid surface at the point of contact and the solid surface, measured inside the liquid. Three surface tensions act at the contact line: solid-air T_sa, solid-liquid T_sl and liquid-air T_la. For equilibrium along the solid, T_sa = T_sl + T_la cos θ, so cos θ = (T_sa − T_sl)/T_la. If T_sa > T_sl, cos θ is positive and θ is acute (water on glass or plastic: the liquid wets the solid). If T_sa < T_sl, cos θ is negative and θ is obtuse (water on a waxy leaf, mercury on glass). If T_sa > T_la + T_sl, no balance is possible and the liquid spreads over the solid. Soaps and detergents reduce the angle of contact so water gets into fabric and lifts the dirt; waterproof paints and wax increase it so rain runs off.

Excess pressure inside drops and bubbles

At a flat surface the surface-tension pulls on a molecule cancel. At a curved surface their components along the normal add up and point towards the centre of curvature, so the pressure on the concave side is greater than on the convex side. That is why small drops and bubbles are spherical and do not collapse. Cut an air bubble of radius R in a liquid into two halves and look at one half. Surface tension pulls on it along the rim, 2πRT; the outside pressure P₁ pushes on the flat face πR² in the same direction; the inside pressure P₂ pushes the other way. Balance: P₂πR² = P₁πR² + 2πRT, so ΔP = P₂ − P₁ = 2T/R for an air bubble in a liquid. A liquid drop also has one surface: ΔP = 2T/R. A soap bubble has two surfaces, so the rim force is 2 × 2πRT and ΔP = 4T/R. The smaller the radius, the greater the excess pressure: tiny fog droplets are so stiff they behave almost like solid balls.

Worked example 2: excess pressures

(a) Soap bubble, R = 1.0 cm, T = 0.030 N m⁻¹: ΔP = 4T/R = 4 × 0.030/0.010 = 12 Pa. (b) Water drop, R = 1.0 mm, T = 0.072 N m⁻¹: ΔP = 2T/R = 2 × 0.072/1.0 × 10⁻³ = 144 Pa. (c) If the soap bubble's excess pressure is balanced by a column of oil of relative density 0.80, the column height is h = ΔP/(ρg) = 12/(800 × 9.8) = 1.5 × 10⁻³ m = 1.5 mm.

Capillarity

A glass tube with a very fine bore ('capilla' is Latin for hair) dipped in water shows the water rising inside it above the outside level; in mercury the level inside is pushed down. The rise or fall of a liquid in a narrow tube is capillarity. It depends on the angle of contact: θ < 90° (adhesion stronger than cohesion, concave meniscus) gives a rise; θ > 90° (cohesion stronger, convex meniscus) gives a fall.

Capillary rise formula. In a tube of radius r, the surface tension acts all round the circle of contact, of length 2πr. Its vertical component T cos θ gives an upward force 2πrT cos θ. This supports the weight of the liquid raised: a column of height h plus the small amount in the curved meniscus, whose volume is πr² × r − (2/3)πr³ = (1/3)πr³. So 2πrT cos θ = πr²(h + r/3)ρg, giving T = rρg(h + r/3)/(2 cos θ). For a very fine tube r/3 is negligible beside h, so T = rρgh/(2 cos θ), or h = 2T cos θ/(rρg). Thus h ∝ 1/r: the narrower the tube, the higher the rise, so h₁r₁ = h₂r₂ for the same liquid.

Worked example 3: rise of water and fall of mercury

(a) Water (T = 0.072 N m⁻¹, θ ≈ 0, ρ = 1000 kg m⁻³) in a glass tube of radius 0.25 mm: h = 2 × 0.072 × 1/(2.5 × 10⁻⁴ × 1000 × 9.8) = 0.144/2.45 = 0.059 m ≈ 5.9 cm. (b) Mercury (T = 0.48 N m⁻¹, θ = 140°, cos 140° = −0.766, ρ = 13 600 kg m⁻³) in a tube of radius 1.0 mm: h = 2 × 0.48 × (−0.766)/(1.0 × 10⁻³ × 13 600 × 9.8) = −0.735/133.3 = −5.5 × 10⁻³ m. The minus sign means the mercury is depressed by about 5.5 mm.

Capillarity and surface tension in daily life

  • Oil rises in the cotton wick of an earthen lamp; water rises through fine channels in plants; blotting paper absorbs ink; tear fluid drains from the eye.
  • Cotton clothes suit summer because their fine pores act as capillaries for sweat.
  • A little oil spread on stagnant water lowers its surface tension, so mosquito eggs laid on the surface sink and are destroyed.
  • Detergents in warm water lower the surface tension and remove dirt; inks and car paints are tuned to form droplets of the right size.
  • Wax makes fabric waterproof by increasing the angle of contact.

T = F/l (N m⁻¹) = surface energy per unit area. Drop or air bubble: ΔP = 2T/R; soap bubble: ΔP = 4T/R. Capillary rise h = 2T cos θ/(rρg); θ < 90° rise, θ > 90° fall.

Key takeaways

  • Surface molecules are pulled inwards, so a liquid surface contracts to the least area.
  • Surface tension (force per length) equals surface energy (work per area).
  • Salt raises the surface tension of water; soap, heating and electrification lower it.
  • An acute angle of contact means wetting and capillary rise; obtuse means a fall.
  • Excess pressure is 2T/R for a drop, 4T/R for a soap bubble; capillary rise is inversely proportional to the radius.

Check your understanding

  1. 1. The excess pressure inside a soap bubble of radius R and surface tension T is:

    1. T/R
    2. 2T/R
    3. 4T/R
    4. 8T/R
    Show answer

    Answer: C. A soap bubble has two surfaces, so the surface-tension force on the rim is 2 × 2πRT = 4πRT. Balancing on πR² gives ΔP = 4T/R. A liquid drop, with one surface, has 2T/R.

  2. 2. Water rises 3.0 cm in a capillary tube. In a tube of the same glass with half the radius, it will rise:

    1. 6.0 cm
    2. 1.5 cm
    3. 12 cm
    4. 3.0 cm
    Show answer

    Answer: A. h = 2T cos θ/(rρg), so h ∝ 1/r and h₁r₁ = h₂r₂. Halving r doubles h: 2 × 3.0 = 6.0 cm.

  3. 3. When a glass capillary tube is dipped in mercury, the mercury level inside the tube:

    1. rises, because the angle of contact is acute
    2. stays level with the outside
    3. rises, because mercury is dense
    4. falls, because the angle of contact is obtuse
    Show answer

    Answer: D. Mercury's angle of contact with glass is obtuse (about 140°), so cos θ is negative and h = 2T cos θ/(rρg) is negative: the level is depressed and the meniscus is convex.

  4. 4. The SI unit of surface tension is:

    1. N m⁻²
    2. N m⁻¹
    3. J m⁻³
    4. N s m⁻²
    Show answer

    Answer: B. Surface tension is force per unit length, N m⁻¹. This equals J m⁻², the unit of surface energy, since 1 J = 1 N m.

  5. 5. A detergent is added to water. Its surface tension and its angle of contact with cloth:

    1. both increase
    2. the surface tension increases and the angle decreases
    3. both stay the same
    4. both decrease
    Show answer

    Answer: D. Soaps and detergents are sparingly soluble substances that lower the surface tension of water, and as wetting agents they reduce the angle of contact, so the water soaks into the fabric and removes dirt.

Privacy · Terms · Refunds · Delivery