- Practice
- About 16 min
- 5 practice questions
Developable surfaces and the position of the light source
Describe cylindrical, conical and zenithal projections with their normal, transverse, oblique, tangent, secant, polar and equatorial cases, and explain gnomonic, stereographic and orthographic projections by the position of the light.
If something looks wrong, please tell us.
By the end of this lesson you can
- Describe the graticule produced by cylindrical, conical and zenithal projections and the regions each suits.
- Distinguish normal, transverse and oblique cylinders, tangent and secant cones, and polar, equatorial and oblique zenithal cases.
- Explain gnomonic, stereographic and orthographic projections from the position of the light source.
The three basic projections are named after the developable surface on to which the graticule is imagined to be projected: a cylinder, a cone or a flat plane. Where the surface touches the globe, the map is most accurate, and distortion grows away from that line or point. This one idea explains why each projection suits a particular part of the world.
Cylindrical projections
Imagine a cylinder wrapped round the globe. When unrolled, the meridians and parallels appear as straight lines crossing at right angles. In the normal case the cylinder touches the globe along the equator, so the equator on the map has its true length, and the projection is suitable for showing equatorial regions. The chapter describes three cases by the line of tangency:
| Case | Line of tangency | Examples named in the chapter |
|---|---|---|
| Normal | The equator | Equirectangular, Mercator, Lambert's cylindrical equal area, Gall's stereographic cylindrical, Miller cylindrical |
| Transverse | A meridian | Cassini, transverse Mercator, transverse cylindrical equal area, modified transverse Mercator |
| Oblique | Another great circle at an angle | Oblique Mercator |
Conical projections
Imagine a cone placed on the globe, touching it along a parallel. After the graticule is projected on to the cone, the cone is cut along one meridian and unfolded. Parallels appear as arcs of circles centred on the apex, and meridians appear as straight lines converging to that point. A conical projection shows only one hemisphere at a time, northern or southern, and is suitable for middle latitudes, where the cone touches. The parallel along which the cone touches is the standard parallel, and the scale is true along it.
- Tangent cone: the cone touches the globe along one standard parallel.
- Secant cone: the cone cuts into the globe and meets it along two parallels, giving two standard parallels and less distortion over a wider belt between them.
Zenithal (azimuthal) projections
Imagine a flat sheet of paper touching the globe at one point. That point becomes the centre of a circular map. In the polar case, meridians passing through the centre are straight lines and the parallels are concentric circles. Directions (azimuths) from the centre are correct, hence the name azimuthal. Zenithal projections are suitable for polar areas. By the point of tangency there are three aspects:
Aspects of zenithal projection
-
Polar zenithal
- Plane tangent at a pole
- Parallels: concentric circles
- Meridians: straight radii
-
Equatorial zenithal
- Plane tangent at a point on the equator
-
Oblique zenithal
- Plane tangent at a point between a pole and the equator
Three developable surfaces
-
Cylindrical
- Touches along the equator (normal case)
- Straight meridians and parallels at right angles
- Best for equatorial regions
-
Conical
- Touches along a standard parallel
- Arcs for parallels, converging straight meridians
- Best for middle latitudes; one hemisphere
-
Zenithal
- Touches at one point
- Circular map; polar case has concentric parallels
- Best for polar areas
Position of the light source
For perspective projections, moving the light source changes the projection. The chapter names three, usually drawn on a plane touching the globe:
| Projection | Position of light | Effect |
|---|---|---|
| Gnomonic | At the centre of the globe | Rays spread widely, so distortion grows very fast away from the centre; cannot show a whole hemisphere |
| Stereographic | On the surface (periphery) of the globe, diametrically opposite the point where the plane touches | Moderate spreading of rays |
| Orthographic | At infinity, opposite the point of contact, so rays are parallel | Parallels crowd together towards the edge; looks like a photograph of the globe |
Cylinder - equator; cone - middle latitudes; plane - poles. Light at centre = gnomonic; at the opposite surface = stereographic; at infinity = orthographic.
Worked example 1: choosing a surface
Choose a developable surface for each map: (i) Antarctica; (ii) the countries of Europe, between about 35° N and 70° N; (iii) the islands of Indonesia, astride the equator. Reasoning: accuracy is greatest where the surface touches. Answer: (i) zenithal, polar case; (ii) conical, ideally secant with two standard parallels within the belt; (iii) cylindrical, normal case.
Worked example 2: identify from the graticule
Identify the surface from the graticule described: (i) straight parallels and straight meridians at right angles; (ii) concentric circles crossed by straight lines radiating from a centre; (iii) parallels as arcs and meridians as straight lines meeting at a point beyond the map. Answer: (i) cylindrical; (ii) polar zenithal; (iii) conical.
Key takeaways: cylindrical projections give straight meridians and parallels and suit equatorial regions (normal, transverse and oblique cases). Conical projections give arc parallels and converging meridians, suit middle latitudes and show one hemisphere; tangent cones have one standard parallel, secant cones two. Zenithal projections give circular maps and suit polar areas (polar, equatorial and oblique aspects). Gnomonic, stereographic and orthographic projections differ in the position of the light.
Check your understanding
-
1. Which projection is most suitable for showing polar areas?
- Conical
- Zenithal
- Normal cylindrical
- Oblique Mercator
Show answer
Answer: B. A plane tangent at a pole gives a circular map centred on the pole, with concentric parallels, so zenithal projections suit polar areas.
-
2. A cylinder whose line of tangency is a meridian gives a:
- normal cylindrical projection
- secant conical projection
- transverse cylindrical projection
- polar zenithal projection
Show answer
Answer: C. When the cylinder touches along a meridian the projection is transverse. Normal means tangent along the equator.
-
3. A secant conical projection has:
- two standard parallels
- one standard parallel
- no standard parallel
- a standard meridian only
Show answer
Answer: A. A secant cone cuts the globe and meets it along two parallels, giving two standard parallels. A tangent cone touches along only one.
-
4. When the source of light is placed at the centre of the globe, the projection is:
- orthographic
- stereographic
- equidistant
- gnomonic
Show answer
Answer: D. Light at the centre gives the gnomonic projection. Light at the opposite end of the diameter gives stereographic, and light at infinity gives orthographic.
-
5. In a conical projection, parallels appear as:
- straight lines at right angles to meridians
- arcs of circles, with meridians converging as straight lines
- concentric circles centred on a pole on the map
- curves that meet at the equator
Show answer
Answer: B. When the cone is unfolded, parallels become arcs centred on the cone's apex, and meridians become straight lines converging towards it.
Sign in to keep track of the lessons you finish.