- Practice
- About 20 min
- 15 practice questions
Final self-assessment: Map Projection
Test yourself on the whole course: 15 questions with answers explained.
If something looks wrong, please tell us.
Attempt all 15 questions first, with a calculator, then check the answers and read each explanation. Use π = 3.1416 and round to two decimal places.
Final self-assessment
-
1. Which statement about map projections is correct?
- A good projection keeps shape, area, distance and direction all correct
- Every projection distorts at least one of shape, area, distance or direction
- Distortion occurs only on small-scale maps
- Only perspective projections are distorted
Show answer
Answer: B. A sphere is not developable, so no projection can keep all properties true at once; it can only keep one or balance them.
-
2. Taking the earth's radius as 6,400 km, a reduced globe of radius 3.2 cm corresponds to a scale of:
- 1:2,000,000
- 1:20,000,000
- 1:200,000,000
- 1:320,000,000
Show answer
Answer: C. 6,400 km = 640,000,000 cm. 640,000,000 ÷ 3.2 = 200,000,000, so the scale is 1:200,000,000.
-
3. In a perspective projection, the graticule is drawn:
- from the shadow cast by a light illuminating the globe on to a developable surface
- only by calculation, without any light
- by tracing a photograph
- by joining places of equal height
Show answer
Answer: A. Perspective projections are made with the help of the shadow cast from an illuminated globe on to a developable surface. Non-perspective projections are calculated.
-
4. For a map of a country lying between 30° N and 50° N, the most suitable developable surface is a:
- normal cylinder
- plane tangent at the pole
- transverse cylinder only
- cone
Show answer
Answer: D. Conical projections are suitable for middle latitudes, and a secant cone with standard parallels inside the belt reduces distortion further.
-
5. In the stereographic projection, the light source is placed:
- at the centre of the globe
- on the globe's surface diametrically opposite the point of contact
- at infinity
- on the equator
Show answer
Answer: B. Stereographic: light at the periphery opposite the point of contact. Gnomonic: light at the centre. Orthographic: light at infinity.
-
6. A zenithal projection with the plane tangent at a point between a pole and the equator is called:
- polar zenithal
- equatorial zenithal
- oblique zenithal
- transverse zenithal
Show answer
Answer: C. The chapter names three aspects: polar (tangent at a pole), equatorial (tangent on the equator) and oblique (tangent between a pole and the equator).
-
7. On a normal cylindrical projection, the 60° parallel is drawn as long as the equator. Compared with the globe, it is stretched by a factor of:
- 2
- 0.5
- 1.15
- 1.41
Show answer
Answer: A. On the globe the 60° parallel is 2πR cos 60° = half the equator. On the map it equals the equator, so it is stretched by 1 ÷ 0.5 = 2.
-
8. Which pair is correctly matched?
- Orthomorphic - equal area
- Homolographic - true shape
- Equidistant - correct area everywhere
- Homolographic - equal area
Show answer
Answer: D. Homolographic means equal area and orthomorphic means true shape. Equidistant projections keep true scale only along some lines.
-
9. A world map comparing the areas under wheat in different countries should use which kind of projection?
- Equal area
- True shape
- Gnomonic
- Any projection, since areas are always true
Show answer
Answer: A. Areas must be comparable, so an equal area projection is needed. On a true-shape projection high-latitude countries would look too large.
-
10. On a cylindrical equal area projection with R = 2 cm, the 60° parallel lies at what distance from the equator? (sin 60° = 0.866)
- 2.09 cm
- 1.73 cm
- 1 cm
- 2 cm
Show answer
Answer: B. Distance = R sin φ = 2 × 0.866 = 1.732, about 1.73 cm. 2.09 cm would be the equidistant spacing for two intervals of 30°.
-
11. On a cylindrical equidistant projection with R = 2 cm and a 30° interval, the spacing between parallels is about:
- 1 cm
- 0.52 cm
- 1.05 cm
- 2.09 cm
Show answer
Answer: C. Meridian length = πR = 6.283 cm for 180°. Spacing = 6.283 × 30 ÷ 180 = 1.047, about 1.05 cm, the same as the meridian interval 2πR ÷ 12.
-
12. In which projection does the distance between parallels decrease towards the poles while meridians stay equally spaced?
- Cylindrical equidistant
- Polar zenithal equidistant
- Gnomonic
- Cylindrical equal area
Show answer
Answer: D. In Lambert's cylindrical equal area projection the parallels lie at R sin φ from the equator, so they crowd together towards the poles, balancing the east-west stretch.
-
13. For a polar zenithal equal area projection with R = 5 cm, the radius of the 60° parallel is: (sin 15° = 0.2588)
- 2.59 cm
- 2.62 cm
- 5 cm
- 1.29 cm
Show answer
Answer: A. r = 2R sin((90° - 60°) ÷ 2) = 10 × sin 15° = 10 × 0.2588 = 2.588, about 2.59 cm. 2.62 cm is the equidistant radius (arc).
-
14. For a polar zenithal equidistant projection with R = 4 cm and a 15° interval, how many circles are drawn from the pole to the equator, and what is the spacing?
- 3 circles, 2.09 cm apart
- 6 circles, 1.05 cm apart
- 6 circles, 2.09 cm apart
- 12 circles, 1.05 cm apart
Show answer
Answer: B. Number of intervals = 90 ÷ 15 = 6. Spacing = 2π × 4 × 15 ÷ 360 = 25.133 ÷ 24 = 1.047, about 1.05 cm. Check: 6 × 1.047 = 6.28 cm = quarter circumference.
-
15. The polar zenithal equal area projection is used mainly for:
- navigation charts of the tropics
- political and distribution maps of polar regions
- maps of the equatorial belt only
- maps where shapes must be perfect everywhere
Show answer
Answer: B. The chapter states it is used for political and distribution maps of polar regions, and for general maps of large areas in the northern hemisphere.
Questions 1-3: lesson 1 (meaning and classification). Questions 4-6: lesson 2 (surfaces and light source). Questions 7-9: lesson 3 (properties). Questions 10-12: lesson 4 (cylindrical constructions). Questions 13-15: lesson 5 (polar zenithal constructions).
Sign in to keep track of the lessons you finish.