• Practice
  • About 30 min
  • 15 practice questions

Final self-assessment: Electronics and Communication

Test yourself on the whole course: 15 questions with answers explained.

If something looks wrong, please tell us.

Attempt all 15 questions in one sitting of about 30 minutes, with a rough sheet for the numericals and without looking back at the lessons. The questions mix ideas from all five lessons and are a little harder than the lesson checks. Check your answers only after you finish, and read every explanation, including those for questions you got right.

Final self-assessment

  1. 1. At room temperature, which change increases the conductivity of pure silicon the most for practical devices?

    1. Cooling it towards 0 K
    2. Doping it with a small amount of phosphorus
    3. Making the crystal larger
    4. Removing all impurities
    Show answer

    Answer: B. A pentavalent dopant such as phosphorus gives nearly one free electron per atom, because only about 0.05 eV frees a donor electron, while freeing an intrinsic electron needs 1.1 eV. Cooling reduces conduction; purifying leaves only the few intrinsic carriers.

  2. 2. In p-type silicon the minority carriers are:

    1. Holes
    2. Positive ions
    3. Acceptor atoms
    4. Electrons
    Show answer

    Answer: D. Trivalent acceptors provide holes, so holes are the majority carriers; the few thermally generated electrons are the minority carriers. Ions are fixed and do not carry current.

  3. 3. An LED made of a material with E_g = 1.9 eV emits light of wavelength about:

    1. 653 nm
    2. 1.9 nm
    3. 236 nm
    4. 1130 nm
    Show answer

    Answer: A. λ ≈ 1240/E_g = 1240/1.9 = 653 nm, which is red light.

  4. 4. A silicon diode (0.7 V drop) and a 470 Ω resistor are in series across a 5.4 V supply, with the diode forward biased. The current is:

    1. 11.5 mA
    2. 10.0 mA
    3. 1.0 mA
    4. 4.7 mA
    Show answer

    Answer: B. Voltage across the resistor = 5.4 − 0.7 = 4.7 V. I = 4.7/470 = 0.010 A = 10.0 mA. (11.5 mA would ignore the diode drop.)

  5. 5. In a Zener regulator, the input voltage rises while the load stays the same. What happens?

    1. The output voltage rises by the same amount
    2. The Zener current falls
    3. The extra voltage appears across the series resistor and the Zener current rises
    4. The diode stops conducting
    Show answer

    Answer: C. The Zener holds V_Z across itself and the parallel load. The rise in input appears across R_s, so I_s rises; since I_L = V_Z/R_L is unchanged, the extra current flows through the Zener (I_Z = I_s − I_L rises).

  6. 6. The rectifier that uses both half cycles with only two diodes needs:

    1. A centre-tapped transformer
    2. No transformer at all
    3. A Zener diode
    4. An LC tank circuit
    Show answer

    Answer: A. The full-wave rectifier in the Tamil Nadu textbook uses a centre-tapped transformer: each diode conducts in one half cycle, and the centre tap is the zero reference.

  7. 7. For a transistor, I_B = 40 μA and I_C = 4.0 mA. Its α is about:

    1. 100
    2. 0.01
    3. 0.99
    4. 1.01
    Show answer

    Answer: C. β = I_C/I_B = 4.0 mA/0.040 mA = 100. α = β/(1 + β) = 100/101 = 0.99. (Equivalently I_E = 4.04 mA and α = 4.0/4.04 = 0.99.)

  8. 8. A transistor used as a closed (ON) switch is operated in the:

    1. Active region
    2. Cut-off region
    3. Breakdown region
    4. Saturation region
    Show answer

    Answer: D. In saturation both junctions are forward biased and the collector current is at its maximum, so the transistor acts as a closed switch. Cut-off is the open switch; the active region is for amplification.

  9. 9. In a CE circuit with V_CC = 9.0 V, R_C = 1.5 kΩ and β = 150, the base current is 20 μA. V_CE is:

    1. 4.5 V
    2. 3.0 V
    3. 6.0 V
    4. 7.5 V
    Show answer

    Answer: A. I_C = βI_B = 150 × 20 μA = 3.0 mA. V_CE = V_CC − I_C R_C = 9.0 − (3.0 × 10⁻³ × 1500) = 9.0 − 4.5 = 4.5 V.

  10. 10. An LC oscillator has L = 100 μH and C = 1.0 nF. Its frequency is about:

    1. 5.0 kHz
    2. 503 kHz
    3. 1.6 MHz
    4. 50 kHz
    Show answer

    Answer: B. f = 1/(2π√(LC)) = 1/(2π√(1.0 × 10⁻⁴ × 1.0 × 10⁻⁹)) = 1/(2π × 3.16 × 10⁻⁷) = 1/(1.99 × 10⁻⁶) = 5.03 × 10⁵ Hz ≈ 503 kHz.

  11. 11. A NOR gate is equivalent to:

    1. An OR gate with inverted inputs
    2. A NAND gate
    3. An AND gate with inverted inputs
    4. An Ex-OR gate
    Show answer

    Answer: C. De Morgan's first theorem: NOT(A + B) = A̅·B̅, which is an AND gate whose inputs are inverted (a bubbled AND).

  12. 12. The output of an Ex-OR gate with inputs A = 1 and B = 1 is fed, together with C = 1, into an AND gate. The final output is:

    1. 1
    2. Undefined
    3. It depends on positive or negative logic only
    4. 0
    Show answer

    Answer: D. Ex-OR gives 1 only when its inputs differ; with A = B = 1 its output is 0. Then AND(0, 1) = 0.

  13. 13. Which statement about FM compared with AM is correct, as given in the Tamil Nadu textbook?

    1. FM has much less noise but needs a wider channel
    2. FM needs a narrower channel than AM
    3. FM covers a larger area than AM
    4. FM equipment is simpler and cheaper
    Show answer

    Answer: A. FM greatly reduces noise and gives better sound, but it needs a much wider channel, more complex and costly equipment, and its reception covers a smaller area.

  14. 14. Transmitting and receiving antennas are 72 m and 50 m high; R = 6400 km. The maximum line-of-sight distance between them is about:

    1. 30 km
    2. 56 km
    3. 25 km
    4. 112 km
    Show answer

    Answer: B. d_T = √(2 × 6.4 × 10⁶ × 72) = √(9.216 × 10⁸) = 30.4 km; d_R = √(2 × 6.4 × 10⁶ × 50) = √(6.4 × 10⁸) = 25.3 km. d = 30.4 + 25.3 = 55.7 km, about 56 km.

  15. 15. The region where neither the ground wave nor the sky wave is received is called the:

    1. Skip distance
    2. Ionosphere
    3. Line of sight
    4. Skip zone
    Show answer

    Answer: D. Beyond the range of the ground wave and before the point where the sky wave first returns (the skip distance), there is no reception: this region is the skip zone.

Questions 1-3: lesson 1 and lesson 3 (semiconductors and the LED). Questions 4-6: lesson 2 (diodes, Zener regulator and rectifiers). Questions 7-9: lessons 3 and 4 (transistor gains, switch and load line). Questions 10-12: lesson 4 (oscillator, logic gates and De Morgan). Questions 13-15: lesson 5 (communication).

Sign in to keep track of the lessons you finish.

Privacy · Terms · Refunds · Delivery