Revision notes

Unit 2 Current Electricity: Foundation

The key points, rules to remember, tables and diagrams from all 5 lessons, on one page for quick revision. To keep a copy, use your browser's Print and choose "Save as PDF".

Lesson 1

Electric current, drift velocity and current density

How a steady drift develops

  1. Battery sets up a field A potential difference creates a field E along the wire.
  2. Electrons accelerate Each free electron gains velocity opposite to E between collisions: a = eE/m.
  3. Collisions with ions After about τ seconds a collision scatters the electron in a random direction.
  4. Net drift On average the electrons creep along at v_d = eEτ/m, opposite to E, giving a steady current.

I = dQ/dt; I = neAv_d; J = I/A = nev_d; v_d = (eτ/m)E = μE; J = σE with σ = ne²τ/m.

  • Current is the rate of flow of charge, I = dQ/dt; 1 A = 1 C s⁻¹; it is a scalar.
  • Conventional current flows from + to − outside the source, opposite to electron flow.
  • Electrons drift slowly (about 10⁻⁴ m s⁻¹) opposite to E; the field itself spreads almost instantly.
  • I = neAv_d, J = nev_d, and J⃗ = σE⃗ is Ohm's law at the microscopic level.
Read the full lesson

Lesson 2

Ohm's law, resistivity, combinations of resistors and temperature dependence

Resistivity at 20 °C, according to the Tamil Nadu textbook (Table 2.1)
ClassMaterialρ (Ω m)
ConductorSilver1.6 × 10⁻⁸
ConductorCopper1.7 × 10⁻⁸
ConductorAluminium2.7 × 10⁻⁸
ConductorTungsten5.6 × 10⁻⁸
ConductorIron10 × 10⁻⁸
SemiconductorGermanium0.46
SemiconductorSilicon640
InsulatorPure water2.5 × 10⁵
InsulatorGlass10¹⁰ to 10¹⁴
InsulatorHard rubber10¹³ to 10¹⁶
InsulatorFused quartz10¹⁶

Series and parallel resistors

  • Series
    • Same current through each
    • Voltages add
    • R_S = R₁ + R₂ + …
    • R_S larger than the largest
  • Parallel
    • Same voltage across each
    • Currents add
    • 1/R_P = 1/R₁ + 1/R₂ + …
    • R_P smaller than the smallest
Resistor colour code
ColourDigitMultiplierTolerance
Black01-
Brown110¹-
Red210²-
Orange310³-
Yellow410⁴-
Green510⁵-
Blue610⁶-
Violet710⁷-
Grey810⁸-
White910⁹-
Gold-10⁻¹5%
Silver-10⁻²10%
No colour--20%
Temperature coefficients of resistivity, according to the Tamil Nadu textbook (selected rows of Table 2.3)
Materialα ((°C)⁻¹)
Copper3.9 × 10⁻³
Silver3.8 × 10⁻³
Tungsten4.5 × 10⁻³
Iron5.0 × 10⁻³
Nichrome0.4 × 10⁻³
Carbon−0.5 × 10⁻³
Germanium−48 × 10⁻³
Silicon−75 × 10⁻³

V = IR; R = ρl/A; series R_S = ΣR; parallel 1/R_P = Σ(1/R); R_T = R₀[1 + α(T − T₀)].

  • Ohm's law V = IR holds for ohmic conductors at constant temperature; the I-V graph is a straight line of slope 1/R.
  • R = ρl/A; resistivity is a property of the material; stretching a wire n times multiplies R by n².
  • Series: same current, R adds. Parallel: same voltage, 1/R adds.
  • Colour code: two digits, multiplier, tolerance (gold 5%, silver 10%, none 20%).
  • Metals: α > 0. Semiconductors: α < 0. Superconductors: R = 0 below T_c.
Read the full lesson

Lesson 3

Electric power and energy, emf, internal resistance and combinations of cells

n identical cells (emf ε, internal resistance r) with load R

  • Series
    • emf nε, internal resistance nr
    • I = nε/(nr + R)
    • Useful when r ≪ R
    • Gives a higher voltage
  • Parallel
    • emf ε, internal resistance r/n
    • I = nε/(r + nR)
    • Useful when r ≫ R
    • Shares the current among cells

P = VI = I²R = V²/R; 1 kWh = 3.6 × 10⁶ J. V = ε − Ir; r = (ε − V)R/V. Series cells: I = nε/(nr + R). Parallel cells: I = nε/(r + nR).

  • Power is the rate of energy delivery, P = VI; in a resistor P = I²R = V²/R.
  • Bills count energy in kWh (units), 1 kWh = 3.6 × 10⁶ J.
  • In series the higher-resistance (lower-rated) bulb glows brighter; in parallel the higher-rated bulb does.
  • Terminal voltage V = ε − Ir is less than the emf whenever current flows.
  • Series cells for large R, parallel cells for small R.
Read the full lesson

Lesson 4

Kirchhoff's rules, Wheatstone's bridge and the meter bridge

Solving a circuit with Kirchhoff's rules

  1. Label currents Give each branch a current with an assumed direction.
  2. Junction rule Use current in = current out to reduce the number of unknowns.
  3. Loop rule Write ΣIR = Σε for enough independent loops, with careful signs.
  4. Solve and interpret Solve the equations; a negative current flows opposite to the assumed direction.

Junction rule: ΣI = 0 (charge conservation). Loop rule: ΣIR = Σε (energy conservation). Bridge balance: P/Q = R/S. Meter bridge: P = Q l₁/(100 − l₁); ρ = Pπa²/l.

  • Current in = current out at every junction.
  • Round any loop, ΣIR = Σε, with +IR along the current and +ε from − to + through a cell.
  • A negative answer only reverses the assumed direction.
  • Wheatstone's bridge is balanced (no galvanometer current) when P/Q = R/S.
  • The meter bridge uses the two lengths of a uniform wire as two arms; interchange P and Q to cancel end resistance.
Read the full lesson

Lesson 5

Potentiometer, Joule's heating effect and thermoelectric effects

Using a potentiometer

  1. Steady primary current Battery drives a constant current I along the uniform wire.
  2. Connect the test cell Positive terminals of both cells go to the same end of the wire.
  3. Slide the jockey Find the point where the galvanometer shows no deflection.
  4. Read the balancing length ε = Irl, so emfs or voltages are in the ratio of balancing lengths.

Thermoelectric effects

  • Seebeck effect
    • Temperature difference between two junctions gives an emf
    • Thermocouple, thermopile, Seebeck generators
  • Peltier effect
    • Current through a junction of two metals
    • Heat absorbed at one junction, evolved at the other
  • Thomson effect
    • Temperature difference along one conductor gives a p.d.
    • Positive in copper, negative in iron

Potentiometer: ε = Irl, ε₁/ε₂ = l₁/l₂, r = R(l₁ − l₂)/l₂. Joule's law: H = I²Rt = VIt.

  • At balance a potentiometer draws no current from the cell, so it measures the true emf; ε ∝ balancing length.
  • Heat produced H = I²Rt: proportional to I², R and t.
  • Nichrome for heating elements; low-melting fuse wires or circuit breakers for protection.
  • Seebeck: ΔT gives an emf; Peltier: current gives heating and cooling at junctions; Thomson: the same within one conductor. All three are reversible.
Read the full lesson

Privacy · Terms · Refunds · Delivery