- Practice
- About 24 min
- 5 practice questions
Kirchhoff's rules, Wheatstone's bridge and the meter bridge
Apply Kirchhoff's current and voltage rules with correct signs, derive the Wheatstone bridge balance condition P/Q = R/S, and use the meter bridge to find an unknown resistance and the resistivity of a wire.
If something looks wrong, please tell us.
By the end of this lesson you can
- State Kirchhoff's current rule and link it to conservation of charge.
- State Kirchhoff's voltage rule, link it to conservation of energy and apply its sign rules.
- Solve a two-loop circuit and interpret a negative answer.
- Derive the balance condition of Wheatstone's bridge.
- Use the meter bridge to find an unknown resistance and the resistivity of its wire, and remove end errors.
Series and parallel rules handle simple circuits. A circuit with several batteries, or resistors that are neither in series nor in parallel, needs two general rules given by Gustav Kirchhoff. They are applied once the currents have reached a steady state.
Kirchhoff's first rule: the current (junction) rule
The algebraic sum of the currents at any junction of a circuit is zero. Take currents entering the junction as positive and currents leaving as negative. Equivalently, the total current flowing in equals the total current flowing out. This is conservation of charge: charge cannot build up at, or vanish from, a junction.
Worked example 1: a junction
At a junction, currents of 3.0 A and 2.0 A flow in, 1.5 A flows out along one wire, and the current I in a fourth wire is unknown. Taking I as leaving: 3.0 + 2.0 − 1.5 − I = 0, so I = 3.5 A, leaving the junction. A negative answer would simply mean the current enters.
Kirchhoff's second rule: the voltage (loop) rule
In any closed loop, the algebraic sum of the products of current and resistance in each part equals the total emf in the loop: ΣIR = Σε. It follows from conservation of energy: the energy supplied by the sources equals the energy delivered to the resistors. Choose a direction to go round the loop (clockwise, say) and use these signs:
- Going through a resistor in the direction of its current: +IR. Against its current: −IR.
- Going through a cell from its negative to its positive terminal: +ε. From positive to negative: −ε.
- Assume a direction for each unknown current. If the answer is negative, the current actually flows the other way; its size is still correct.
Solving a circuit with Kirchhoff's rules
- Label currents Give each branch a current with an assumed direction.
- Junction rule Use current in = current out to reduce the number of unknowns.
- Loop rule Write ΣIR = Σε for enough independent loops, with careful signs.
- Solve and interpret Solve the equations; a negative current flows opposite to the assumed direction.
Worked example 2: a circuit with two batteries
Three branches join two points X and Y. Branch 1 has a 10 V cell and a 2 Ω resistor; branch 2 has a 4 V cell and a 1 Ω resistor; branch 3 has only a 4 Ω resistor. Both cells have their positive terminals towards X, and their internal resistances are neglected. Let I₁ flow up branch 1 to X and I₂ up branch 2 to X; by the junction rule, I₃ = I₁ + I₂ flows down branch 3. Loop 1 (branches 1 and 3): 2I₁ + 4(I₁ + I₂) = 10, i.e. 6I₁ + 4I₂ = 10. Loop 2 (branches 2 and 3): 1I₂ + 4(I₁ + I₂) = 4, i.e. 4I₁ + 5I₂ = 4. Solve: multiply the first by 5 and the second by 4: 30I₁ + 20I₂ = 50 and 16I₁ + 20I₂ = 16. Subtract: 14I₁ = 34, I₁ = 17/7 ≈ 2.43 A. Then 5I₂ = 4 − 4(17/7) = −40/7, so I₂ = −8/7 ≈ −1.14 A. I₃ = 17/7 − 8/7 = 9/7 ≈ 1.29 A. Check loop 1: 2(17/7) + 4(9/7) = 70/7 = 10 V. Meaning: I₂ is negative, so 1.14 A actually flows down through the 4 V cell, into its positive terminal: the 10 V cell is charging it.
Wheatstone's bridge
Four resistances P, Q, R and S form a loop ABCD: P from A to B, Q from B to C, R from A to D and S from D to C. A battery is connected between A and C, and a galvanometer G (a sensitive instrument for detecting small currents) between B and D. Let I₁, I₂, I₃, I₄ be the currents in P, R, Q, S and I_G the galvanometer current. Junction rule at B and D: I₁ − I_G − I₃ = 0 and I₂ + I_G − I₄ = 0. Loop rule for ABDA: I₁P + I_GG − I₂R = 0; for ABCDA: I₁P + I₃Q − I₄S − I₂R = 0.
The bridge is balanced when B and D are at the same potential, so no current flows through the galvanometer: I_G = 0. Then I₁ = I₃ and I₂ = I₄, and the first loop equation gives I₁P = I₂R. The second loop equation then gives I₃Q = I₄S. Dividing: P/Q = R/S. This is the balance condition; only then does the galvanometer show null deflection. If three resistances are known, the fourth can be found, or two can be compared.
Worked example 3: a balanced bridge
In a balanced Wheatstone bridge P = 20 Ω, Q = 60 Ω and R = 15 Ω. Find S. S = QR/P = (60 × 15)/20 = 900/20 = 45 Ω. Check: P/Q = 20/60 = 1/3 and R/S = 15/45 = 1/3.
The meter bridge
The meter bridge is a practical Wheatstone bridge. A uniform manganin wire AB, one metre long, is stretched along a metre scale between two thick copper strips; a third copper strip in between leaves two gaps, G₁ and G₂. The unknown resistance P goes in G₁ and a known resistance Q (from a resistance box) in G₂. A jockey (sliding contact) is joined to the middle strip through a galvanometer and a high resistance, and a cell (for example a Leclanché cell) and key are connected across the ends of the wire. The jockey is moved along the wire until the galvanometer shows zero deflection at a point J. The two parts of the wire act as the other two arms: if r is the resistance per unit length, R = r × AJ = rl₁ and S = r × JB = rl₂. Balance gives P/Q = l₁/l₂, so P = Q l₁/l₂ = Q l₁/(100 − l₁) with lengths in cm.
End resistance. Imperfect soldering where the wire meets the copper strips adds small unknown resistances. To remove this error, take a second set of readings with P and Q interchanged and average the two values of P. Resistivity. If the unknown P is a wire of length l and radius a, then from R = ρl/A, ρ = Pπa²/l.
Worked example 4: unknown resistance and resistivity
With Q = 4.0 Ω in the right gap, balance is found at l₁ = 60.0 cm. Step 1: l₂ = 100 − 60.0 = 40.0 cm, so P = 4.0 × 60.0/40.0 = 6.0 Ω. Step 2: the unknown is a wire 1.5 m long of radius 0.10 mm = 1.0 × 10⁻⁴ m. Area πa² = 3.14 × 1.0 × 10⁻⁸ = 3.14 × 10⁻⁸ m². Step 3: ρ = PA/l = (6.0 × 3.14 × 10⁻⁸)/1.5 ≈ 1.26 × 10⁻⁷ Ω m.
Junction rule: ΣI = 0 (charge conservation). Loop rule: ΣIR = Σε (energy conservation). Bridge balance: P/Q = R/S. Meter bridge: P = Q l₁/(100 − l₁); ρ = Pπa²/l.
Key takeaways
- Current in = current out at every junction.
- Round any loop, ΣIR = Σε, with +IR along the current and +ε from − to + through a cell.
- A negative answer only reverses the assumed direction.
- Wheatstone's bridge is balanced (no galvanometer current) when P/Q = R/S.
- The meter bridge uses the two lengths of a uniform wire as two arms; interchange P and Q to cancel end resistance.
Check your understanding
-
1. Kirchhoff's current rule is a consequence of the conservation of:
- energy
- momentum
- charge
- mass
Show answer
Answer: C. Charge cannot accumulate at or disappear from a junction, so the current flowing in must equal the current flowing out. The voltage rule is the one that comes from energy conservation.
-
2. At a junction, currents of 5 A and 3 A enter and currents of 2 A and I leave. The value of I is:
- 10 A
- 4 A
- 0 A
- 6 A
Show answer
Answer: D. Current in = current out: 5 + 3 = 2 + I, so I = 6 A.
-
3. In a balanced Wheatstone bridge P = 100 Ω, Q = 500 Ω and R = 30 Ω. The fourth resistance S is:
- 150 Ω
- 6 Ω
- 1667 Ω
- 16.7 Ω
Show answer
Answer: A. P/Q = R/S, so S = QR/P = (500 × 30)/100 = 150 Ω.
-
4. In a meter bridge, a 12 Ω resistance is in the right gap and the balance point is 40 cm from the left end. The unknown resistance in the left gap is:
- 18 Ω
- 8 Ω
- 4.8 Ω
- 30 Ω
Show answer
Answer: B. P = Q l₁/(100 − l₁) = 12 × 40/60 = 8 Ω.
-
5. In a meter bridge experiment, the known and unknown resistances are interchanged and the readings repeated. This is done to:
- increase the current
- make the wire uniform
- eliminate the error due to end resistances
- change the galvanometer's resistance
Show answer
Answer: C. The joints between the wire and the copper strips add small unknown end resistances. Interchanging P and Q and averaging the two results cancels this error.
Sign in to keep track of the lessons you finish.