- Practice
- About 25 min
- 5 practice questions
Potentiometer, Joule's heating effect and thermoelectric effects
Explain the potentiometer principle and use it to compare emfs and find internal resistance, apply Joule's law H = I²Rt to heaters, fuses, furnaces and lamps, and describe the Seebeck, Peltier and Thomson effects.
If something looks wrong, please tell us.
By the end of this lesson you can
- State the principle of the potentiometer, ε = Irl, i.e. ε ∝ l.
- Compare the emfs of two cells using balancing lengths.
- Find the internal resistance of a cell, r = R(l₁ − l₂)/l₂.
- State and use Joule's law of heating, H = I²Rt.
- Explain electric heaters, fuses and circuit breakers, furnaces and lamps.
- Describe the Seebeck, Peltier and Thomson effects and their uses.
A voltmeter draws a little current, so it never reads the true emf of a cell. The potentiometer measures a potential difference at balance, when no current is drawn at all, which makes it more accurate. This lesson then turns to what current does to a conductor (heating it) and the reverse link, where a temperature difference produces an emf.
The potentiometer
A potentiometer is a long uniform wire of manganin or constantan, commonly ten metres in ten parallel rows of one metre, stretched on a wooden board beside a metre scale, with a jockey for making contact. Primary circuit: a battery Bt and a key drive a steady current I through the whole wire CD. Secondary circuit: the cell to be tested, with its positive terminal joined to the same end C as the positive terminal of Bt, is connected through a galvanometer and a high resistance to the jockey. When the jockey touches a point J where the potential difference across CJ equals the cell's emf, no current flows through the galvanometer. CJ = l is the balancing length. If r is the resistance per unit length, the potential drop along CJ is Irl, so ε = Irl. With I and r constant, ε ∝ l: the emf is proportional to the balancing length. The potential drop per unit length of the wire, Ir, is called the potential gradient.
Comparing the emfs of two cells
The two cells ε₁ and ε₂ are connected to the secondary circuit through a two-way (DPDT) switch, so either can be put in. Find the balancing lengths l₁ and l₂ in turn. Then ε₁ = Irl₁ and ε₂ = Irl₂, so ε₁/ε₂ = l₁/l₂. A rheostat in the primary circuit lets the experiment be repeated with different currents.
Measuring internal resistance
The cell ε is connected in the secondary circuit with a resistance box R and key K₂ across it. With K₂ open, the cell is in open circuit and the balancing length l₁ measures its emf: ε ∝ l₁. With K₂ closed, a current flows through R and the cell, and the balancing length l₂ measures the terminal voltage V = εR/(R + r): V ∝ l₂. Dividing, (R + r)/R = l₁/l₂, so 1 + r/R = l₁/l₂ and r = R(l₁ − l₂)/l₂. Repeating with different R, the textbook notes that the internal resistance is found to increase as the external resistance is increased.
Using a potentiometer
- Steady primary current Battery drives a constant current I along the uniform wire.
- Connect the test cell Positive terminals of both cells go to the same end of the wire.
- Slide the jockey Find the point where the galvanometer shows no deflection.
- Read the balancing length ε = Irl, so emfs or voltages are in the ratio of balancing lengths.
Worked example 1: potentiometer measurements
(a) The potential difference across a 10 m potentiometer wire is 2.0 V. The potential gradient is 2.0/10 = 0.20 V m⁻¹. A cell balances at 6.5 m, so its emf is 0.20 × 6.5 = 1.3 V. (b) A cell of emf 1.5 V balances at 300 cm and a second cell at 220 cm on the same wire. ε₂ = 1.5 × 220/300 = 1.1 V. (c) A cell balances at l₁ = 280 cm on open circuit and at l₂ = 240 cm when shunted by R = 12 Ω. r = R(l₁ − l₂)/l₂ = 12 × 40/240 = 2.0 Ω.
Heating effect of current: Joule's law
When a current I flows for time t through a conductor across which the potential difference is V, the electrical energy spent is W = VIt. With no other effect (no motor turning, no chemical change), all of it heats the conductor: H = VIt, and for a resistance R, H = I²Rt. Joule verified this experimentally. Joule's law of heating: the heat produced varies directly as (i) the square of the current, (ii) the resistance and (iii) the time for which the current flows. The reverse link, a temperature difference producing an emf, is the thermoelectric effect at the end of this lesson.
Worked example 2: heat produced
A current of 2.0 A flows through a 50 Ω resistor for 10 minutes. H = I²Rt = (2.0)² × 50 × 600 = 4 × 50 × 600 = 1.2 × 10⁵ J = 120 kJ.
Worked example 3: an electric kettle
A kettle element of resistance 26.45 Ω works on 230 V. How long does it take to heat 1.5 kg of water from 25 °C to 100 °C, assuming no heat is lost? (Specific heat capacity of water 4200 J kg⁻¹ K⁻¹.) Step 1: P = V²/R = 230²/26.45 = 52 900/26.45 = 2000 W. Step 2: heat needed Q = msΔT = 1.5 × 4200 × 75 = 472 500 J. Step 3: t = Q/P = 472 500/2000 ≈ 236 s, about 3.9 minutes. In practice it takes a little longer, as some heat escapes.
Applications of Joule heating
- Electric heaters: irons, room heaters and toasters use heating elements of nichrome, an alloy of nickel and chromium, which has a high resistivity and can be heated to high temperatures without oxidising.
- Fuses: a short wire of low melting point connected in series with a circuit; it melts and breaks the circuit when the current exceeds a safe value. According to the textbook, a lead-tin alloy is used for current ratings below 15 A and copper wire above that. A burnt fuse must be replaced, so homes now often use circuit breakers (trippers), which switch off on excess current and can be switched on again after the fault is repaired.
- Electric furnaces: used to make materials such as steel, silicon carbide, quartz and gallium arsenide. The textbook gives about 1500 °C with molybdenum-nichrome wire wound on a silica tube, and up to about 3000 °C for carbon arc furnaces.
- Electric lamps: a tungsten filament (tungsten has a very high melting point) in a glass bulb is heated until it glows. The textbook notes that only about 5% of the electrical energy becomes light; the rest is wasted as heat. Electric discharge lamps, electric welding and electric arcs also use the heating effect.
Thermoelectric effects
The conversion of a temperature difference into a voltage, and of a voltage into a temperature difference, is the thermoelectric effect.
Seebeck effect. In a closed circuit of two different metals, an emf is produced when the two junctions are kept at different temperatures, and a thermoelectric current flows. Two dissimilar metals joined at two junctions form a thermocouple (for example copper and iron, one junction in ice and the other heated). Interchanging the hot and cold junctions reverses the current, so the effect is reversible. The emf depends on (i) the pair of metals and (ii) the temperature difference between the junctions. Uses: thermoelectric (Seebeck) generators that turn waste heat in power plants into electricity, automotive thermoelectric generators that improve fuel efficiency, and thermocouples and thermopiles for measuring temperature differences.
Peltier effect. Discovered by Peltier in 1834: when a current is passed through a thermocouple whose junctions are at the same temperature, heat is absorbed at one junction and evolved at the other. In a Cu-Fe thermocouple, as described in the textbook, the junction where the current flows from Cu to Fe cools and the junction where it flows from Fe to Cu heats up. Reversing the current reverses the roles of the junctions, so this effect is also reversible.
Thomson effect. Thomson showed that if two points of the same conductor are at different temperatures, the density of electrons differs and a potential difference appears between them. If a current is passed along a bar heated at its middle, heat is absorbed in one half and evolved in the other. In copper (also silver, zinc, cadmium) heat is carried in the direction of the current: the positive Thomson effect. In iron (also platinum, nickel, cobalt, mercury) heat is carried opposite to the current: the negative Thomson effect. It too is reversible.
Thermoelectric effects
-
Seebeck effect
- Temperature difference between two junctions gives an emf
- Thermocouple, thermopile, Seebeck generators
-
Peltier effect
- Current through a junction of two metals
- Heat absorbed at one junction, evolved at the other
-
Thomson effect
- Temperature difference along one conductor gives a p.d.
- Positive in copper, negative in iron
Potentiometer: ε = Irl, ε₁/ε₂ = l₁/l₂, r = R(l₁ − l₂)/l₂. Joule's law: H = I²Rt = VIt.
Key takeaways
- At balance a potentiometer draws no current from the cell, so it measures the true emf; ε ∝ balancing length.
- Heat produced H = I²Rt: proportional to I², R and t.
- Nichrome for heating elements; low-melting fuse wires or circuit breakers for protection.
- Seebeck: ΔT gives an emf; Peltier: current gives heating and cooling at junctions; Thomson: the same within one conductor. All three are reversible.
Check your understanding
-
1. On a potentiometer wire, a cell of emf 1.2 V balances at 240 cm. A second cell balances at 300 cm. Its emf is:
- 0.96 V
- 1.5 V
- 1.2 V
- 2.0 V
Show answer
Answer: B. ε₂/ε₁ = l₂/l₁, so ε₂ = 1.2 × 300/240 = 1.5 V.
-
2. A cell balances at 150 cm on open circuit and at 125 cm when a 10 Ω resistance is connected across it. Its internal resistance is:
- 2 Ω
- 12 Ω
- 0.5 Ω
- 8.3 Ω
Show answer
Answer: A. r = R(l₁ − l₂)/l₂ = 10 × (150 − 125)/125 = 10 × 25/125 = 2 Ω.
-
3. If the current through a heater coil is doubled, keeping its resistance the same, the heat produced in the same time becomes:
- twice
- half
- the same
- four times
Show answer
Answer: D. H = I²Rt, so H ∝ I². Doubling I multiplies H by 2² = 4.
-
4. Nichrome is used for the heating elements of electric irons because it:
- has a low resistivity and melts easily
- is a superconductor
- has a high resistivity and does not oxidise easily when red hot
- has a negative temperature coefficient
Show answer
Answer: C. A heating element needs a high resistivity (so a manageable length gives enough resistance) and must stand high temperatures without oxidising. Nichrome has both properties.
-
5. When the two junctions of a copper-iron circuit are kept at different temperatures, a current flows in it. This is the:
- Seebeck effect
- Peltier effect
- Thomson effect
- Joule effect
Show answer
Answer: A. An emf produced by a temperature difference between two junctions of dissimilar metals is the Seebeck effect, the principle of the thermocouple. The Peltier effect is the reverse: a current producing heating and cooling at the junctions.
Sign in to keep track of the lessons you finish.