• Practice
  • About 16 min
  • 5 practice questions

The screw gauge: pitch, least count and zero error

Explain how a screw gauge works, calculate its pitch and least count, find positive and negative zero error and measure the thickness of thin wires and sheets.

If something looks wrong, please tell us.

By the end of this lesson you can

  • Name the parts of a screw gauge.
  • State the principle of the screw gauge.
  • Calculate pitch and least count.
  • Find positive and negative zero error and the zero correction.
  • Calculate the correct thickness of a wire, coin or sheet.

The diameter of a thin wire or the thickness of a metal sheet is often less than a millimetre. A screw gauge measures such sizes to 1/100 of a millimetre, that is 0.01 mm, ten times finer than a Vernier caliper.

Parts of a screw gauge

  • U-shaped frame: holds all the other parts.
  • Hollow cylinder (sleeve): fixed to one end of the frame; its inner surface has grooves through which the screw turns.
  • Pitch scale (PS): a millimetre scale marked on the cylinder along the screw's axis.
  • Thimble with head scale (HS): turns with the screw; its rim is divided into 100 equal divisions.
  • Spindle: the flat end of the screw that moves towards the object.
  • Anvil (stud): fixed to the other arm of the frame, opposite the spindle.
  • Ratchet: a safety device that slips once the object is gripped, so the user cannot press too hard.

Principle, pitch and least count

The screw gauge works on this principle: when a screw turns in a nut, the distance moved by its tip is directly proportional to the number of rotations. The pitch is the distance the tip moves for one complete rotation of the head: pitch = distance moved on the pitch scale ÷ number of rotations. In a typical gauge it is 1 mm.

The least count is the distance moved when the head turns by just one head scale division: L.C. = pitch ÷ number of head scale divisions = 1 mm ÷ 100 = 0.01 mm.

Zero error

Turn the ratchet until the spindle touches the anvil. If the zero of the head scale lies exactly on the axis line of the pitch scale, there is no zero error.

Zero error of a screw gauge

  • Positive zero error
    • Head scale zero is BELOW the pitch scale axis
    • Coinciding division n is read directly
    • Zero error = + (n × L.C.)
    • Zero correction is negative
  • Negative zero error
    • Head scale zero is ABOVE the pitch scale axis
    • Coinciding division n is near 100
    • Zero error = − (100 − n) × L.C.
    • Zero correction is positive

Taking a reading

Measuring with a screw gauge

  1. Find pitch and L.C. Usually 1 mm and 0.01 mm
  2. Check zero error Spindle touching anvil
  3. Grip the object Turn by the ratchet only
  4. Read PSR Last mm mark visible on the pitch scale
  5. Read HSC Head scale division on the axis line
  6. Correct reading PSR + (HSC × L.C.) + zero correction

Worked example 1: a thin wire, no zero error

Question: For a copper wire, PSR = 0 mm and HSC = 46. L.C. = 0.01 mm and there is no zero error. Find the diameter and the radius. Working: Diameter = 0 + (46 × 0.01) = 0.46 mm. Radius = 0.46 ÷ 2 = 0.23 mm.

Worked example 2: positive zero error

Question: With the spindle touching the anvil, the 4th head scale division lies on the axis, below zero. A coin then gives PSR = 2 mm and HSC = 35. Find the correct thickness. Working: Zero error = +4 × 0.01 = +0.04 mm; zero correction = −0.04 mm. Observed = 2 + (35 × 0.01) = 2.35 mm. Correct thickness = 2.35 − 0.04 = 2.31 mm.

Worked example 3: negative zero error

Question: With the spindle touching the anvil, the 97th head scale division lies on the axis. A metal sheet gives PSR = 1 mm and HSC = 18. Find its thickness. Working: Zero error = −(100 − 97) × 0.01 = −0.03 mm; zero correction = +0.03 mm. Observed = 1 + (18 × 0.01) = 1.18 mm. Correct thickness = 1.18 + 0.03 = 1.21 mm.

Measuring one sheet of paper

A single sheet is too thin to read well. Press a neat stack of, say, 100 sheets between the spindle and anvil, measure the stack and divide by 100. If 100 sheets measure 8.50 mm, one sheet is 8.50 ÷ 100 = 0.085 mm. Measuring many and dividing reduces the effect of small reading errors.

Pitch = distance moved ÷ rotations. L.C. = pitch ÷ head scale divisions = 0.01 mm. Correct reading = PSR + (HSC × L.C.) + zero correction.

Key takeaways: the screw gauge uses the steady advance of a screw to magnify tiny lengths. With a 1 mm pitch and 100 head divisions its least count is 0.01 mm. Find the zero error before measuring, and always turn by the ratchet so the object is not squeezed.

Check your understanding

  1. 1. What is the principle of a screw gauge?

    1. The distance moved by a screw's tip is directly proportional to the number of rotations
    2. A spring stretches in proportion to the load
    3. Light travels in straight lines
    4. Two scales of different length are compared
    Show answer

    Answer: A. When a screw rotates in a nut, its tip advances by one pitch for each full turn, so the distance moved is directly proportional to the number of rotations. The spring idea is Hooke's law, used in the spring balance.

  2. 2. The head of a screw gauge moves 5 mm along the pitch scale in 10 rotations, and the head scale has 50 divisions. What is its least count?

    1. 0.1 mm
    2. 0.5 mm
    3. 0.01 mm
    4. 0.05 mm
    Show answer

    Answer: C. Pitch = 5 mm ÷ 10 = 0.5 mm. L.C. = pitch ÷ head divisions = 0.5 ÷ 50 = 0.01 mm.

  3. 3. Why is a screw gauge fitted with a ratchet?

    1. To read the head scale
    2. To stop the user pressing the object too hard
    3. To measure depth
    4. To lock the pitch scale
    Show answer

    Answer: B. The ratchet slips once the spindle grips the object, so the user cannot apply undue pressure that would squeeze the object and spoil the reading.

  4. 4. With the spindle touching the anvil, the 92nd head scale division lies on the axis line. What is the zero error? (L.C. = 0.01 mm)

    1. +0.92 mm
    2. +0.08 mm
    3. −0.92 mm
    4. −0.08 mm
    Show answer

    Answer: D. A coinciding division near 100 means the head zero is above the axis: a negative error. Zero error = −(100 − 92) × 0.01 = −0.08 mm, so the zero correction is +0.08 mm.

  5. 5. PSR = 1 mm and HSC = 68 for a coin, with no zero error and L.C. = 0.01 mm. What is its thickness?

    1. 1.68 mm
    2. 1.068 mm
    3. 6.8 mm
    4. 0.68 mm
    Show answer

    Answer: A. Thickness = PSR + (HSC × L.C.) = 1 + (68 × 0.01) = 1 + 0.68 = 1.68 mm.

Privacy · Terms · Refunds · Delivery