• Practice
  • About 16 min
  • 5 practice questions

Pressure in liquids and the formula P = hρg

Show that liquids press in all directions, list what liquid pressure depends on, derive P = hρg for a liquid column and use it in calculations.

If something looks wrong, please tell us.

By the end of this lesson you can

  • Explain why a fluid exerts pressure in all directions.
  • Name the three factors that liquid pressure depends on.
  • Derive P = hρg for a liquid column.
  • Calculate liquid pressure at a given depth.

All flowing substances, liquids and gases, are called fluids. Like solids, fluids have weight, so they exert pressure. Their particles are in constant, rapid motion and move equally in every direction, so the pressure of a fluid acts in all directions and at every point, and the force it exerts on any surface is perpendicular to that surface.

Liquids press downward, upward and sideways

  • Downward: stretch a balloon over one end of a plastic pipe, hold it upright and pour water in; the balloon bulges out at the bottom.
  • Upward: push an air-filled ball under water and let go; it shoots up, because the water pushes it upward.
  • Sideways (lateral): make a small hole in the side of a plastic bottle full of water; water spurts out sideways.

What liquid pressure depends on

Make holes one above another down the side of a tall plastic can and fill it with water (do it outdoors or over a sink, and ask an adult to help push the holes through with a heated or sharp nail). Water barely dribbles from the top hole but squirts furthest from the bottom hole: pressure increases with depth. At any one depth, the pressure is the same in all directions. Fill two identical cans to the same level, one with water and one with cooking oil, with holes at the same height: water squirts out harder because it is denser. So liquid pressure at a point depends on:

  1. the depth h below the liquid surface,
  2. the density ρ (rho) of the liquid,
  3. the acceleration due to gravity g.

Deriving P = hρg

Imagine a column of liquid of height h, cross-sectional area A and density ρ standing in a tall beaker. The thrust on the bottom is the weight of the liquid: F = mg. The mass is density × volume, m = ρV, and the volume of the column is V = Ah, so m = ρAh. Therefore F = ρAhg. Pressure = F/A = ρAhg/A, so P = hρg.

Steps to P = hρg

  1. Thrust = weight F = mg
  2. Mass from density m = ρV
  3. Volume of column V = Ah, so m = ρAh
  4. Thrust F = ρAhg
  5. Divide by area P = F/A = hρg

The area A cancels out. So the pressure at a given depth in a given liquid does not depend on the width or shape of the container. A narrow tube and a wide tank filled to the same height with water have the same pressure at the bottom.

Worked example 1: water and oil

Question: Find the pressure at the bottom of a 0.6 m column of (a) water (ρ = 1000 kg/m³) and (b) an oil (ρ = 900 kg/m³). Take g = 10 m/s². Working: (a) P = hρg = 0.6 × 1000 × 10 = 6000 Pa. (b) P = 0.6 × 900 × 10 = 5400 Pa. The denser liquid gives the greater pressure.

Worked example 2: a diver in a lake

Question: What is the pressure due to the water alone on a diver 12 m below the surface of a lake (ρ = 1000 kg/m³, g = 9.8 m/s²)? Working: P = 12 × 1000 × 9.8 = 117 600 Pa, about 1.18 × 10⁵ Pa. That is more than the whole pressure of the atmosphere at sea level, so divers wear special suits and equipment.

Worked example 3: finding density

Question: The pressure at the bottom of a 0.5 m deep tank of a liquid is 4000 Pa (g = 10 m/s²). Find the liquid's density. Working: ρ = P ÷ (hg) = 4000 ÷ (0.5 × 10) = 4000 ÷ 5 = 800 kg/m³, which could be kerosene.

Pressure in a liquid: P = hρg. It increases with depth and density, is the same in all directions at one depth, and does not depend on the container's shape.

Key takeaways: fluids press in all directions, perpendicular to every surface. Liquid pressure depends on depth, density and g, and is given by P = hρg. That is why dams are built thicker at the base and why deep-sea divers need protective suits.

Check your understanding

  1. 1. Water spurts out of holes in the side of a can. Which hole sends water out with the greatest force?

    1. The top hole
    2. The middle hole
    3. All holes equally
    4. The bottom hole
    Show answer

    Answer: D. Pressure in a liquid increases with depth (P = hρg), so the bottom hole, being deepest, has the greatest pressure behind it.

  2. 2. On which of these does the pressure at the bottom of a liquid column NOT depend?

    1. Depth of the liquid
    2. Area of the base of the container
    3. Density of the liquid
    4. Acceleration due to gravity
    Show answer

    Answer: B. In the derivation the area A cancels, leaving P = hρg. So the pressure depends on depth, density and g, but not on the area of the base.

  3. 3. What is the pressure at a depth of 2 m in water (ρ = 1000 kg/m³, g = 10 m/s²)?

    1. 20 000 Pa
    2. 2000 Pa
    3. 200 Pa
    4. 5000 Pa
    Show answer

    Answer: A. P = hρg = 2 × 1000 × 10 = 20 000 Pa.

  4. 4. Kerosene (800 kg/m³) and water (1000 kg/m³) fill two tanks to the same height. Compared with the water tank, the pressure at the bottom of the kerosene tank is

    1. the same
    2. greater
    3. less, in the ratio 4 : 5
    4. zero
    Show answer

    Answer: C. With equal h and g, pressure is proportional to density. 800 : 1000 = 4 : 5, so the kerosene tank has less pressure.

  5. 5. Why is the wall of a dam made thicker at the bottom than at the top?

    1. Water is warmer at the bottom
    2. The pressure of water increases with depth
    3. Water presses only at the bottom
    4. To make the dam look stable
    Show answer

    Answer: B. Water pressure grows with depth, so the lower part of the wall must withstand the greatest pressure and is built thicker.

Privacy · Terms · Refunds · Delivery