• Practice
  • About 16 min
  • 5 practice questions

Describing test scores: mean, median, mode, range and standard deviation

Calculate and interpret the three averages, the range and the standard deviation for a set of test scores, and see how outliers and skew change which average is fairest.

If something looks wrong, please tell us.

After a test, a teacher has a list of marks. To make sense of it she needs one number for the typical score and one for how spread out the scores are. Exam questions ask you to calculate these quickly and to choose the right average when a few scores are unusual.

Measures of central tendency

MeasureHow to find itBest used when
MeanAdd all scores and divide by the number of scoresScores are fairly symmetrical with no extreme values
MedianArrange in order; take the middle score, or the average of the two middle scoresThere are extreme scores, or the data are ordinal
ModeThe most frequent score; there may be none or more than oneYou want the most common value or the data are nominal

The mean uses every score, so one very high or very low score pulls it. The median depends only on position, so it resists extremes. The mode ignores the size of the other scores.

Spread: range and standard deviation

Two classes can have the same mean and yet be very different. The range is the highest score minus the lowest; it is quick but depends on just two scores. The standard deviation (SD) shows how far scores typically lie from the mean. To find it for a whole group: subtract the mean from each score, square each difference, add the squares, divide by the number of scores to get the variance, then take the square root. A large SD means a widely spread class; an SD of zero means every score is the same.

Skewness

In a positively skewed distribution most scores are low and a few are high, so the tail points to the right and the mean is greater than the median. In a negatively skewed distribution most scores are high and a few are low, so the tail points left and the mean is less than the median. A very easy test tends to give negative skew; a very hard test tends to give positive skew.

Worked example 1: all the measures

Ten students score 8, 10, 12, 12, 14, 14, 14, 16, 18, 22 out of 25. Step 1: sum = 140, so mean = 140 ÷ 10 = 14. Step 2: the scores are already in order; the 5th and 6th are 14 and 14, so the median = (14 + 14) ÷ 2 = 14. Step 3: 14 appears three times, so the mode = 14. Step 4: range = 22 − 8 = 14. Because the mean, median and mode agree, the scores are roughly symmetrical.

Worked example 2: an extreme score

Five students score 12, 14, 15, 16 and 18. The mean is 75 ÷ 5 = 15 and the median is 15. A sixth student then scores 45. Step 1: the new total is 75 + 45 = 120, so the mean = 120 ÷ 6 = 20. Step 2: the order is now 12, 14, 15, 16, 18, 45; the middle two are 15 and 16, so the median = 15.5. Step 3: the mean rose by 5 marks while the median rose by 0.5. Answer: with one extreme score the median describes a typical student better, and the mean is greater than the median, which signals positive skew.

Worked example 3: same mean, different spread

Class A scores 10, 10, 10, 10, 10. Class B scores 6, 8, 10, 12, 14. Both means are 10. Step 1: for Class A every deviation is 0, so SD = 0. Step 2: for Class B the deviations are −4, −2, 0, 2 and 4; their squares are 16, 4, 0, 4 and 16, which add to 40. Step 3: the variance = 40 ÷ 5 = 8, and SD = √8, about 2.83. Answer: Class B is more spread out, so one lesson pitched at the average will fit its students less well. The teacher might plan different tasks for the top and bottom groups.

Mean is pulled by extremes; median is the middle and resists them; mode is the most common. Positive skew: mean above median. Negative skew: mean below median.

— Rule to remember

Key takeaways

  • Choose the median when a few scores are extreme.
  • Range uses only two scores; SD uses all of them.
  • SD is zero only when every score is identical.
  • Positive skew means a right tail and a mean above the median.
  • Equal means do not mean equal classes: always check spread.

Check your understanding

  1. 1. Scores of a group are 5, 7, 7, 9 and 12. The mean score is:

    1. 7
    2. 9
    3. 8
    4. 10
    Show answer

    Answer: C. Total = 5 + 7 + 7 + 9 + 12 = 40, and 40 ÷ 5 = 8. The median and the mode are both 7.

  2. 2. For the scores 4, 6, 8 and 10, the median is:

    1. 7
    2. 6
    3. 8
    4. 9
    Show answer

    Answer: A. There are four scores, so average the two middle ones: (6 + 8) ÷ 2 = 7.

  3. 3. A very easy test is taken by a class. The distribution of marks is most likely:

    1. Positively skewed, with the mean above the median
    2. Perfectly symmetrical, with the mean equal to the mode
    3. Skewed, but with the median above the range
    4. Negatively skewed, with the mean below the median
    Show answer

    Answer: D. Most students score high and a few score low, so the tail points left and the mean falls below the median.

  4. 4. Which measure of spread is found only from the highest and lowest scores?

    1. Standard deviation
    2. Range
    3. Variance
    4. Mean deviation
    Show answer

    Answer: B. Range is highest minus lowest. The other measures use every score in the group.

  5. 5. Two classes both have a mean of 40, but Class P has an SD of 3 and Class Q has an SD of 12. Which statement is correct?

    1. Class Q's scores are more widely spread than Class P's
    2. Class P's scores are more widely spread than Class Q's
    3. Both classes have the same spread because their means match
    4. Class Q must have the higher median than Class P
    Show answer

    Answer: A. A larger SD means scores lie further from the mean on average. Equal means say nothing about spread, and nothing here fixes the medians.

Privacy · Terms · Refunds · Delivery