- Foundation
- About 15 min
- 5 practice questions
Electric charge, current and the electric circuit
Explain what an electric current is, use I = Q/t to find current, charge or time, count the electrons in a given charge, and measure current with an ammeter in a closed circuit.
If something looks wrong, please tell us.
By the end of this lesson you can
- Define electric current and its SI unit, the ampere.
- Use I = Q/t and the charge of an electron (1.6 × 10⁻¹⁹ C) in calculations.
- Describe a closed circuit, conventional current and how an ammeter is connected.
Fans, lights, phones and water pumps all run on electricity. To understand them we need to know what actually moves in a wire, how we measure it, and what makes it move. This lesson starts with the moving part: electric charge.
Electric current
In a metal wire, some electrons are free to move. When they drift steadily in one direction, charge flows through the wire. The electric current is the rate at which charge flows: the amount of charge passing any cross-section of the wire per second.
Electric current I = Q ÷ t, where Q is the net charge (in coulomb) flowing in time t (in seconds). 1 ampere = 1 coulomb per second.
The SI unit of charge is the coulomb (C). The charge on one electron is 1.6 × 10⁻¹⁹ C (negative), so one coulomb is the charge of about 6.25 × 10¹⁸ electrons. The SI unit of current is the ampere (A), named after the French scientist André-Marie Ampère. Small currents are written in milliampere (1 mA = 10⁻³ A) or microampere (1 µA = 10⁻⁶ A).
The circuit and the direction of current
Charge flows only around a complete, unbroken path called a closed electric circuit. If the path is broken, for example when a switch is off, the current stops and the bulb goes out. When electricity was first studied, current was thought of as a flow of positive charge, so the conventional direction of current is from the positive terminal of the cell, through the circuit, to the negative terminal. Electrons, being negative, actually move the opposite way.
Two directions to remember
-
Conventional current
- From the positive terminal to the negative terminal outside the cell
- Used in all circuit diagrams and rules
-
Electron flow
- From the negative terminal to the positive terminal
- Opposite to the conventional current
Current is measured by an ammeter, which is always connected in series in the circuit, so that the whole current passes through it. The current is the same at every point of a single loop, so it does not matter where in the loop the ammeter is placed.
A simple closed circuit
- Cell Provides the push on the charges.
- Plug key (switch) Closes or breaks the path.
- Ammeter Connected in series to measure current.
- Bulb Glows while current flows.
- Back to the cell The path must be complete for current to flow.
Worked example 1: charge from current
A current of 0.4 A flows through a torch bulb for 5 minutes. How much charge passes? Working: t = 5 × 60 = 300 s. Q = I × t = 0.4 × 300 = 120 C.
Worked example 2: number of electrons
How many electrons make up the 120 C of example 1? Working: number of electrons n = Q ÷ e = 120 ÷ (1.6 × 10⁻¹⁹) = (120 ÷ 1.6) × 10¹⁹ = 75 × 10¹⁹ = 7.5 × 10²⁰ electrons.
Worked example 3: current from charge
30 C of charge passes through a wire in 1 minute. Find the current. Working: I = Q ÷ t = 30 ÷ 60 = 0.5 A.
Key takeaways: current is the rate of flow of charge, I = Q ÷ t, measured in ampere (1 A = 1 C/s). One electron carries 1.6 × 10⁻¹⁹ C, so n = Q ÷ e. Current flows only in a closed circuit. Conventional current goes from + to − outside the cell, opposite to the electron flow. An ammeter is connected in series.
Check your understanding
-
1. The SI unit of electric current is the
- volt
- ampere
- coulomb
- ohm
Show answer
Answer: B. Current is measured in ampere (A); 1 A is a flow of 1 coulomb of charge per second. The volt measures potential difference, the coulomb charge and the ohm resistance.
-
2. A current of 2 A flows for 2 minutes. The charge that flows is
- 4 C
- 60 C
- 120 C
- 240 C
Show answer
Answer: D. t = 2 × 60 = 120 s. Q = I × t = 2 × 120 = 240 C.
-
3. The conventional direction of electric current is
- opposite to the direction of flow of electrons
- the same as the direction of flow of electrons
- always from the negative terminal outside the cell
- different in every circuit
Show answer
Answer: A. Conventional current was defined as the flow of positive charge, from + to − outside the cell. Electrons are negative and move from − to +, so conventional current is opposite to electron flow.
-
4. How should an ammeter be connected to measure the current through a bulb?
- In parallel with the bulb
- Across the cell only
- In series with the bulb
- It does not need to be connected
Show answer
Answer: C. An ammeter must have the whole current pass through it, so it is connected in series with the component.
-
5. If 5 × 10¹⁸ electrons pass a point in a wire every second, the current is
- 0.8 A
- 5 A
- 1.6 A
- 8 A
Show answer
Answer: A. Charge per second = 5 × 10¹⁸ × 1.6 × 10⁻¹⁹ C = 8 × 10⁻¹ C = 0.8 C. So I = 0.8 A.
Sign in to keep track of the lessons you finish.