- Foundation
- About 18 min
- 5 practice questions
Ohm's law, resistance and resistivity
State Ohm's law and use V = IR, describe the factors on which the resistance of a wire depends, and use R = ρl/A to calculate resistance and compare materials.
If something looks wrong, please tell us.
By the end of this lesson you can
- State Ohm's law and solve problems with V = IR.
- Explain how length, area of cross-section, material and temperature affect resistance.
- Use R = ρl/A and explain why different materials are used for wires and heating elements.
Connect the same cell to a short thick copper wire and then to a long thin nichrome wire, and the currents are very different. Every conductor opposes the flow of charge to some extent. This opposition is its resistance. Georg Simon Ohm found a simple relationship between current and potential difference.
Ohm's law
If the potential difference across a metal wire is increased step by step (for example by adding cells or adjusting a rheostat), the current increases in the same proportion, provided the temperature stays the same. A graph of V against I is a straight line through the origin.
Ohm's law: the potential difference across a conductor is directly proportional to the current through it, provided its temperature remains the same. V = I × R.
The constant R is the resistance. Its SI unit is the ohm (Ω): a conductor has a resistance of 1 Ω if a current of 1 A flows through it when the potential difference across it is 1 V. For a given potential difference, the current is inversely proportional to the resistance: doubling R halves I. A rheostat is a component whose resistance can be changed, used to control the current in a circuit.
Worked example 1: using V = IR
A potential difference of 6 V is applied across a 12 Ω resistor. Find the current. Working: I = V ÷ R = 6 ÷ 12 = 0.5 A.
Worked example 2: reading an Ohm's law table
A student records these illustrative readings for a wire: 1.5 V with 0.1 A, 3.0 V with 0.2 A, 4.5 V with 0.3 A, and 6.0 V with 0.4 A. Working: V ÷ I = 1.5 ÷ 0.1 = 15; 3.0 ÷ 0.2 = 15; 4.5 ÷ 0.3 = 15; 6.0 ÷ 0.4 = 15. The ratio is constant, so the wire obeys Ohm's law and its resistance is 15 Ω.
What does the resistance of a wire depend on?
Factors affecting the resistance of a conductor
-
Length (l)
- Directly proportional
- Double the length, double the resistance
-
Area of cross-section (A)
- Inversely proportional
- A thicker wire has less resistance
-
Material
- Measured by its resistivity ρ
- Copper low, nichrome much higher
-
Temperature
- For metals, resistance rises as temperature rises
R = ρ × l ÷ A, where ρ (rho) is the resistivity of the material, in ohm metre (Ω m).
Resistivity is a property of the material (it changes with temperature) and does not depend on the length or thickness of the wire. Metals and alloys have very low resistivity, roughly 10⁻⁸ Ω m to 10⁻⁶ Ω m, and are good conductors. Insulators such as rubber and glass have resistivity of the order of 10¹² to 10¹⁷ Ω m.
| Material | Resistivity | Typical use |
|---|---|---|
| Copper, aluminium | Very low | Connecting wires and power transmission lines |
| Tungsten | Low, but very high melting point | Filaments of electric bulbs |
| Alloys such as nichrome | Much higher than pure metals; do not oxidise (burn) readily when hot | Heating elements of irons, toasters and heaters |
| Rubber, glass, plastic | Extremely high | Insulation |
Worked example 3: using R = ρl/A
A wire of resistivity 1.0 × 10⁻⁶ Ω m is 2 m long with a cross-sectional area of 0.5 mm². Find its resistance. Working: A = 0.5 mm² = 0.5 × 10⁻⁶ m². R = ρl ÷ A = (1.0 × 10⁻⁶ × 2) ÷ (0.5 × 10⁻⁶) = 2 ÷ 0.5 = 4 Ω.
Worked example 4: stretching a wire
A wire of resistance R is stretched to twice its length. Its volume stays the same. Working: if the length becomes 2l, the area must become A/2 (since volume = l × A is unchanged). New resistance = ρ(2l) ÷ (A/2) = 4 × ρl/A = 4R.
Key takeaways: Ohm's law says V = IR at constant temperature, and resistance is measured in ohm. The resistance of a wire is proportional to its length, inversely proportional to its area of cross-section, and depends on its material and temperature: R = ρl/A. Resistivity is a property of the material alone. Copper and aluminium carry current; alloys such as nichrome make heating elements.
Check your understanding
-
1. A bulb draws 0.25 A from a 3 V battery. Its resistance is
- 0.75 Ω
- 12 Ω
- 3.25 Ω
- 1.2 Ω
Show answer
Answer: B. R = V ÷ I = 3 ÷ 0.25 = 12 Ω.
-
2. The length of a wire is doubled while its area of cross-section is kept the same. Its resistance
- is halved
- stays the same
- becomes four times
- doubles
Show answer
Answer: D. R = ρl/A. With A and ρ unchanged, R is proportional to l, so doubling the length doubles the resistance.
-
3. The resistivity of a wire depends on
- its material and temperature
- its length
- its area of cross-section
- the current through it
Show answer
Answer: A. Resistivity is a property of the material and changes with temperature. Length and area change the resistance of a particular wire but not the resistivity of its material.
-
4. Two wires are made of the same metal and have the same length. Wire Q has twice the diameter of wire P. If P has resistance 8 Ω, Q has resistance
- 16 Ω
- 4 Ω
- 2 Ω
- 32 Ω
Show answer
Answer: C. Doubling the diameter makes the area of cross-section 2² = 4 times larger, so the resistance becomes one quarter: 8 ÷ 4 = 2 Ω.
-
5. Why are the heating elements of electric irons usually made of an alloy rather than a pure metal?
- Alloys have very low resistivity
- Alloys have higher resistivity and do not oxidise readily at high temperature
- Alloys are always cheaper than copper
- Alloys do not get hot
Show answer
Answer: B. A heating element needs a high resistance to produce heat, and it must not burn away when red hot. Alloys such as nichrome have higher resistivity than pure metals and do not oxidise readily.
Sign in to keep track of the lessons you finish.