- Foundation
- About 15 min
- 5 practice questions
Potential difference and circuit diagrams
Explain potential difference as work done per unit charge, use V = W/Q, measure it with a voltmeter, and read and draw circuit diagrams using standard symbols.
If something looks wrong, please tell us.
By the end of this lesson you can
- Define potential difference and the volt, and use V = W/Q.
- Connect a voltmeter correctly and explain the role of a cell or battery.
- Recognise the standard symbols used in circuit diagrams.
Water flows in a pipe only if there is a pressure difference between its ends. In the same way, charges flow in a wire only when there is an electric pressure difference, called potential difference, between its ends. A cell or battery supplies it.
Potential difference
Inside a cell, chemical reactions separate charge and create a potential difference between its terminals, even when no current is drawn. When the cell is connected in a circuit, this potential difference sets the charges moving, and the cell uses up its stored chemical energy doing so.
Potential difference V = W ÷ Q: the work done to move a unit charge from one point to another. 1 volt = 1 joule per coulomb.
The SI unit of potential difference is the volt (V), named after Alessandro Volta. The potential difference between two points is 1 V when 1 J of work is done to move 1 C of charge from one point to the other. Potential difference is measured with a voltmeter, which is always connected in parallel across the points between which the potential difference is wanted.
Ammeter and voltmeter
-
Ammeter
- Measures current
- Unit: ampere
- Connected in series
- Has very low resistance
-
Voltmeter
- Measures potential difference
- Unit: volt
- Connected in parallel across a component
- Has very high resistance
Worked example 1: finding the potential difference
18 J of work is done in moving 3 C of charge between two points. Find the potential difference. Working: V = W ÷ Q = 18 ÷ 3 = 6 V.
Worked example 2: finding the work done
How much work is done in moving 4 C of charge through a potential difference of 9 V? Working: W = V × Q = 9 × 4 = 36 J. In other words, a 9 V battery gives 9 J of energy to every coulomb that passes through it.
Circuit diagrams
Drawing real-looking cells and bulbs takes time, so scientists use simple standard symbols. A circuit diagram shows how components are connected, not what they look like.
| Component | How its symbol is drawn |
|---|---|
| Electric cell | A long thin line (positive terminal) and a short thick line (negative terminal), side by side |
| Battery | Two or more cell symbols joined in a row |
| Plug key or switch (open) | A gap in the line, or a key shown open |
| Plug key or switch (closed) | The gap bridged |
| Wire joint | Two lines crossing with a solid dot at the join |
| Wires crossing without joining | One line hopping over the other, with no dot |
| Electric bulb | A circle with a cross or a small loop inside |
| Resistor | A small rectangle (or zig-zag line) |
| Rheostat (variable resistance) | A resistor symbol with an arrow across it |
| Ammeter / voltmeter | A circle with A inside / a circle with V inside |
Worked example 3: reading a circuit
A circuit has a battery, a closed key, a bulb and an ammeter in a single loop, with a voltmeter drawn across the bulb. Reading it: the battery, key, bulb and ammeter are in series, so the same current flows through each and the ammeter reads it. The voltmeter is in parallel with the bulb, so it reads the potential difference across the bulb only. If the key is opened, the loop is broken: the ammeter reads zero, and so does the voltmeter across the bulb, because with no current through the bulb there is no potential difference across it.
Key takeaways: a potential difference is needed to make charges flow; a cell maintains one by chemical action. V = W ÷ Q, and 1 V = 1 J/C. A voltmeter is connected in parallel and an ammeter in series. Circuit diagrams use standard symbols to show connections clearly.
Check your understanding
-
1. 24 J of work is done in moving 2 C of charge between two points. The potential difference is
- 48 V
- 12 V
- 22 V
- 0.08 V
Show answer
Answer: B. V = W ÷ Q = 24 ÷ 2 = 12 V.
-
2. How much energy does a 12 V battery give to each coulomb of charge passing through it?
- 1 J
- 6 J
- 24 J
- 12 J
Show answer
Answer: D. By V = W ÷ Q, W = V × Q = 12 × 1 = 12 J for each coulomb.
-
3. A voltmeter used to measure the potential difference across a resistor must be connected
- in parallel across the resistor
- in series with the resistor
- in series with the cell only
- anywhere, since it does not matter
Show answer
Answer: A. A voltmeter compares the potential at two points, so it is connected in parallel across the component.
-
4. What maintains the potential difference between the terminals of a dry cell?
- Friction inside the cell
- Magnetism of the cell's case
- Chemical action inside the cell
- Heat from the surroundings
Show answer
Answer: C. Chemical reactions inside the cell separate charges and keep its terminals at different potentials.
-
5. Assertion (A): Current flows through a wire only when there is a potential difference across its ends.
Reason (R): The potential difference makes the free charges in the wire move, much as a pressure difference makes water flow in a pipe.- Both A and R are true, and R is the correct explanation of A
- Both A and R are true, but R is not the correct explanation of A
- A is true, but R is false
- A is false, but R is true
Show answer
Answer: A. Both are true, and the potential difference is exactly what drives the charges, so R correctly explains A.
Sign in to keep track of the lessons you finish.