• Foundation
  • About 20 min
  • 5 practice questions

Heating effect of current and electric power

Use Joule's law H = I²Rt, explain how heaters, bulbs and fuses use the heating effect, calculate electric power with P = VI = I²R = V²/R, and work out energy in kilowatt hours.

If something looks wrong, please tell us.

By the end of this lesson you can

  • Derive and use Joule's law of heating, H = I²Rt.
  • Explain practical uses of the heating effect, including bulbs and fuses.
  • Calculate electric power and electrical energy in joules and kilowatt hours (units).

An electric iron, a toaster and a room heater all turn electrical energy into heat. Even a phone charger becomes warm. This heating happens whenever current flows through a resistance. This lesson measures that heat and the rate at which appliances use energy.

Joule's law of heating

A source of potential difference V that drives a current I for time t does work W = V × I × t. If all of this energy is spent in a resistor R, it appears as heat H. Using V = IR, H = VIt = (IR)It = I²Rt.

Joule's law of heating: H = I² × R × t. Heat produced is proportional to the square of the current, to the resistance and to the time.

Heat produced in a resistor (H = I²Rt)

  • Current I
    • Proportional to I²
    • Doubling the current gives four times the heat
  • Resistance R
    • Proportional to R for a given current
  • Time t
    • Proportional to the time for which current flows

Worked example 1: heat produced

A current of 2 A flows through a 10 Ω resistor for 1 minute. Find the heat produced. Working: t = 60 s. H = I²Rt = 2² × 10 × 60 = 4 × 10 × 60 = 2400 J.

Uses of the heating effect

  • Heating appliances such as irons, toasters, ovens, kettles and heaters use high-resistance elements that become very hot.
  • Electric bulbs: a thin filament gets so hot that it glows. Tungsten is used because of its very high melting point, and the bulb is filled with chemically inactive gases such as nitrogen and argon to make the filament last longer. Most of the energy still becomes heat, with only a small part given out as light.
  • Electric fuse: a short wire of a metal or alloy with a suitable melting point, connected in series with the appliance. If a current larger than its rating flows, the wire heats up, melts and breaks the circuit, protecting the appliance and wiring. Fuses used at home have ratings such as 1 A, 2 A, 3 A, 5 A and 10 A.

Heating is not always wanted: it wastes energy in connecting wires, motors and computers, and can damage them.

Electric power

Power is the rate at which electrical energy is used or dissipated. Its SI unit is the watt (W): 1 W is the power used when a current of 1 A flows under a potential difference of 1 V. A larger unit is the kilowatt: 1 kW = 1000 W.

Electric power P = V × I = I² × R = V² ÷ R. Energy = power × time; 1 kW h = 3.6 × 10⁶ J.

Worked example 2: a bulb's current and resistance

A bulb is rated 60 W, 220 V. Find the current it draws and its resistance. Working: I = P ÷ V = 60 ÷ 220 ≈ 0.27 A. R = V² ÷ P = 220² ÷ 60 = 48400 ÷ 60 ≈ 806.7 Ω. If the same bulb were run on 110 V, its power would be V² ÷ R = 110² ÷ 806.7 = 12100 ÷ 806.7 ≈ 15 W, one quarter of its rating, because power depends on V².

Paying for electrical energy

Electricity bills charge for energy, not power. The commercial unit of energy is the kilowatt hour (kW h), commonly called one 'unit'. It is the energy used in one hour at a rate of 1 kW: 1 kW h = 1000 W × 3600 s = 3,600,000 J = 3.6 × 10⁶ J.

Worked example 3: energy and cost

A 2 kW room heater runs for 1.5 hours a day for 30 days. Suppose electricity costs ₹6 per unit (an illustrative rate). Working: energy = 2 kW × 1.5 h/day × 30 days = 90 kW h. Cost = 90 × ₹6 = ₹540.

From appliance rating to bill

  1. Power in kW Watts ÷ 1000.
  2. Multiply by hours Energy per day in kW h.
  3. Multiply by days Total units used.
  4. Multiply by rate Cost in rupees.

Key takeaways: current through a resistance produces heat H = I²Rt, so doubling the current gives four times the heat. Heaters, bulbs and fuses use this effect; a fuse in series melts when the current exceeds its rating. Power P = VI = I²R = V²/R, measured in watt. Energy is sold in kilowatt hours, and 1 kW h = 3.6 × 10⁶ J.

Check your understanding

  1. 1. If the current through a heater coil is doubled, the heat produced in the same time becomes

    1. four times
    2. double
    3. half
    4. the same
    Show answer

    Answer: A. H = I²Rt. Doubling I multiplies I² by 2² = 4, so the heat becomes four times.

  2. 2. An appliance draws 5 A from a 220 V supply. Its power is

    1. 44 W
    2. 225 W
    3. 1100 W
    4. 2200 W
    Show answer

    Answer: C. P = V × I = 220 × 5 = 1100 W, i.e. 1.1 kW.

  3. 3. One kilowatt hour is equal to

    1. 1000 J
    2. 3600 J
    3. 3.6 × 10⁵ J
    4. 3.6 × 10⁶ J
    Show answer

    Answer: D. 1 kW h = 1000 W × 3600 s = 3,600,000 J = 3.6 × 10⁶ J.

  4. 4. An electric kettle of 1500 W is used for 20 minutes every day for 30 days. The energy used is

    1. 15 kW h
    2. 45 kW h
    3. 900 kW h
    4. 150 kW h
    Show answer

    Answer: A. Power = 1.5 kW; time per day = 20 min = 1/3 h. Energy = 1.5 × (1/3) × 30 = 0.5 × 30 = 15 kW h.

  5. 5. Assertion (A): A fuse is connected in series with the appliance it protects.
    Reason (R): When a fuse melts, it breaks the only path for current to that appliance.

    1. Both A and R are true, and R is the correct explanation of A
    2. Both A and R are true, but R is not the correct explanation of A
    3. A is true, but R is false
    4. A is false, but R is true
    Show answer

    Answer: A. Both are true. Because the fuse is in series, all the current passes through it, and when it melts the circuit is broken; R correctly explains A.

Sign in to keep track of the lessons you finish.

Next lesson → Final self-assessment: Electricity

Privacy · Terms · Refunds · Delivery