• Foundation
  • About 25 min
  • 15 practice questions

Final self-assessment: Mechanical Properties of Solids

Test yourself on the whole course: 15 questions with answers explained.

If something looks wrong, please tell us.

Attempt all 15 questions in one sitting of about 25 minutes, with a rough sheet for the numericals and without looking back at the lessons. Use g = 9.8 m s⁻² unless a question gives another value. Check your answers only after you finish, and read every explanation, including those for questions you got right.

Final self-assessment

  1. 1. A rubber block 5.0 cm tall has its base fixed; a tangential force moves its top face 1.0 mm sideways. What is the shear angle?

    1. 0.20 rad
    2. 0.020 rad
    3. 0.0020 rad
    4. 2.0 rad
    Show answer

    Answer: B. θ ≈ tan θ = Δx/L = 1.0 mm/50 mm = 0.020 rad. Both lengths are converted to millimetres before dividing.

  2. 2. Which kind of stress changes the volume of a body but not its shape?

    1. Tensile stress
    2. Shearing stress
    3. Compressive stress on two opposite faces only
    4. Hydraulic stress
    Show answer

    Answer: D. Hydraulic stress acts perpendicularly and equally on every part of the surface, so the body shrinks uniformly and keeps its shape. Tensile and compressive stress on two faces change the length; shearing stress changes the shape.

  3. 3. A wire hangs from a ceiling with a weight F at its lower end; its cross-sectional area is A. What is the tensile stress in the wire?

    1. 2F/A, because the ceiling and the weight both pull
    2. F/(2A)
    3. F/A
    4. Zero, because the two pulls cancel
    Show answer

    Answer: C. The ceiling pulls up with F and the weight pulls down with F, but the tension at any cross-section is just F, not 2F. The stress is tension per unit area, F/A.

  4. 4. A wire is loaded beyond its yield point and then unloaded. Which statement is true?

    1. Its strain returns to zero because it is still elastic
    2. It is left with a permanent set: strain remains at zero stress
    3. Its Young's modulus has become zero
    4. It must already have fractured
    Show answer

    Answer: B. Beyond the yield point (elastic limit) deformation is plastic. When the stress is removed the wire does not return to its original length: a permanent set remains. Fracture happens only at the end of the curve.

  5. 5. On a stress-strain graph (made-up data) the straight part passes through stress 1.0 × 10⁸ N m⁻² at strain 5.0 × 10⁻⁴. What is Young's modulus of the material?

    1. 5.0 × 10⁴ N m⁻²
    2. 2.0 × 10¹¹ N m⁻²
    3. 5.0 × 10¹¹ N m⁻²
    4. 2.0 × 10¹² N m⁻²
    Show answer

    Answer: B. Y = slope of the straight part = stress/strain = (1.0 × 10⁸)/(5.0 × 10⁻⁴) = 0.2 × 10¹² = 2.0 × 10¹¹ N m⁻².

  6. 6. Assertion (A): Rubber is more elastic than steel. Reason (R): Rubber stretches much more than steel under the same stress.

    1. Both A and R are true, and R is the correct explanation of A
    2. Both A and R are true, but R is not the correct explanation of A
    3. A is true, but R is false
    4. A is false, but R is true
    Show answer

    Answer: D. R is true: rubber has a far smaller modulus, so it stretches more. But in physics the more elastic material is the one that deforms less for a given stress (larger modulus), so steel is more elastic than rubber and A is false.

  7. 7. A copper wire and a steel wire of the same length and cross-section are joined end to end and loaded. With Y(steel) = 2.0 × 10¹¹ and Y(copper) = 1.1 × 10¹¹ N m⁻², what is extension of copper ÷ extension of steel?

    1. 0.55
    2. 1.0
    3. 1.8
    4. 3.3
    Show answer

    Answer: C. In series both wires carry the same tension F. ΔL = FL/(AY), and F, L and A are equal, so ΔL ∝ 1/Y. Ratio = Y(steel)/Y(copper) = 2.0/1.1 ≈ 1.8.

  8. 8. A wire is replaced by one of the same material with twice the length and twice the radius. For the same load, the extension becomes

    1. twice as large
    2. the same
    3. half as large
    4. four times as large
    Show answer

    Answer: C. ΔL = FL/(πr²Y), so ΔL ∝ L/r². New value ∝ 2L/(2r)² = 2L/(4r²) = ½ (L/r²). The extension is halved.

  9. 9. A steel wire 3.0 m long and 1.0 mm in radius carries a tension of 200 N. With Y = 2.0 × 10¹¹ N m⁻², its extension is closest to

    1. 0.095 mm
    2. 0.95 mm
    3. 9.5 mm
    4. 3.0 mm
    Show answer

    Answer: B. A = π(1.0 × 10⁻³)² = 3.14 × 10⁻⁶ m². ΔL = FL/(AY) = (200 × 3.0)/(3.14 × 10⁻⁶ × 2.0 × 10¹¹) = 600/(6.28 × 10⁵) = 9.55 × 10⁻⁴ m, about 0.95 mm.

  10. 10. A copper cube of edge 10 cm is placed where the pressure on it rises by 2.8 × 10⁷ Pa. Taking B(copper) = 1.4 × 10¹¹ Pa, by how much does its volume decrease?

    1. 0.020 cm³
    2. 2.0 cm³
    3. 0.20 cm³
    4. 20 cm³
    Show answer

    Answer: C. ΔV/V = p/B = (2.8 × 10⁷)/(1.4 × 10¹¹) = 2.0 × 10⁻⁴. V = (10 cm)³ = 1000 cm³, so ΔV = 2.0 × 10⁻⁴ × 1000 = 0.20 cm³.

  11. 11. What is the SI unit of compressibility?

    1. N m⁻²
    2. Pa⁻¹
    3. N m
    4. It has no unit
    Show answer

    Answer: B. Compressibility k = 1/B. Bulk modulus is in Pa (N m⁻²), so k is in Pa⁻¹, that is m² N⁻¹. It is the fractional change in volume (no unit) per unit change in pressure.

  12. 12. A steel wire 1.0 mm in diameter is stretched so that its longitudinal strain is 1.0 × 10⁻³. Its Poisson's ratio is 0.30. By how much does its diameter decrease?

    1. 3.0 × 10⁻⁴ mm
    2. 3.0 × 10⁻³ mm
    3. 1.0 × 10⁻³ mm
    4. 3.3 × 10⁻⁴ mm
    Show answer

    Answer: A. Lateral strain = Poisson's ratio × longitudinal strain = 0.30 × 1.0 × 10⁻³ = 3.0 × 10⁻⁴. Δd = lateral strain × d = 3.0 × 10⁻⁴ × 1.0 mm = 3.0 × 10⁻⁴ mm.

  13. 13. A steel wire (Y = 2.0 × 10¹¹ N m⁻²) has a strain of 2.0 × 10⁻³. What is the elastic energy stored per unit volume?

    1. 2.0 × 10⁵ J m⁻³
    2. 4.0 × 10⁸ J m⁻³
    3. 8.0 × 10⁵ J m⁻³
    4. 4.0 × 10⁵ J m⁻³
    Show answer

    Answer: D. u = ½ Yε² = ½ × 2.0 × 10¹¹ × (2.0 × 10⁻³)² = ½ × 2.0 × 10¹¹ × 4.0 × 10⁻⁶ = 4.0 × 10⁵ J m⁻³. Forgetting the half gives 8.0 × 10⁵.

  14. 14. A centrally loaded beam is replaced by one of the same material and length with twice the breadth and half the depth. The sag under the same load becomes

    1. 4 times as large
    2. the same
    3. one quarter
    4. 16 times as large
    Show answer

    Answer: A. δ = Wl³/(4bd³Y), so δ ∝ 1/(b d³). New: 1/[(2b)(d/2)³] = 1/[2b × d³/8] = 4/(b d³). The sag is 4 times larger, which shows why depth matters more than breadth.

  15. 15. Taking the elastic limit of a rock as 3.0 × 10⁸ N m⁻², its density as 2.5 × 10³ kg m⁻³ and g = 10 m s⁻², the greatest height a mountain of this rock could have is about

    1. 1.2 km
    2. 8.3 km
    3. 30 km
    4. 12 km
    Show answer

    Answer: D. The stress at the base, about hρg, must not exceed the elastic limit: h = (3.0 × 10⁸)/(2.5 × 10³ × 10) = 1.2 × 10⁴ m = 12 km.

Questions 1-3: lesson 1 (stress and strain). Questions 4-6: lesson 2 (Hooke's law and the stress-strain curve). Questions 7-9: lesson 3 (Young's modulus). Questions 10-12: lesson 4 (shear modulus, bulk modulus and Poisson's ratio). Questions 13-15: lesson 5 (elastic energy and applications).

Sign in to keep track of the lessons you finish.

Privacy · Terms · Refunds · Delivery