• Foundation
  • About 20 min
  • 5 practice questions

AC through a resistor, rms values and phasors

Describe a sinusoidal ac voltage, show that current and voltage in a resistor are in phase, derive the average power ½i_m²R and the rms values I = i_m/√2, and represent ac quantities by phasors.

If something looks wrong, please tell us.

By the end of this lesson you can

  • Write an ac voltage as v = v_m sin ωt and explain why ac is preferred for supply.
  • Show that in a pure resistor current and voltage are in phase.
  • Derive the average power in a resistor and define rms current and voltage.
  • Use phasors to represent sinusoidal quantities and their phases.

The mains supply in our homes is an alternating voltage: it varies like a sine function of time, and the current it drives (alternating current, ac) reverses direction many times a second. AC is preferred because transformers can change its voltage easily and efficiently, so electrical energy can be transmitted economically over long distances. AC circuits also have special properties, such as the resonance used to tune a radio.

AC voltage applied to a resistor

Connect a resistor R to a source whose voltage is v = v_m sin ωt, where v_m is the amplitude (peak value) and ω the angular frequency. Kirchhoff's loop rule gives v_m sin ωt = iR, so:

i = i_m sin ωt, with i_m = v_m/R. Ohm's law holds for ac in a resistor, and the current is in phase with the voltage: both reach zero, maximum and minimum at the same instants.

Over a whole cycle the current is positive half the time and negative half the time, so the average current is zero. But that does not mean no energy is used: the heating depends on i², which is never negative.

Average power and rms values

  1. Instantaneous power: p = i²R = i_m²R sin² ωt.
  2. Use sin² ωt = ½(1 − cos 2ωt). The average of cos 2ωt over a cycle is zero, so the average of sin² ωt is ½.
  3. Average power: P = ½ i_m²R.
  4. Define the rms (root mean square) current I so that P = I²R: I² = i_m²/2, so I = i_m/√2.

I = i_m/√2 ≈ 0.707 i_m and V = v_m/√2 ≈ 0.707 v_m. Then V = IR and P = I²R = V²/R = VI, exactly as for dc.

The rms current is the steady (dc) current that would produce the same average heating in the resistor. AC meters read rms values, and stated ac values are rms unless said otherwise: a 220 V supply has peak voltage √2 × 220 ≈ 311 V. The ac ampere itself is defined through this heating effect, because the force between two wires carrying ac would average to zero.

Phasors

To keep track of phases we use phasors: arrows of length equal to the amplitude, rotating anticlockwise about the origin with angular speed ω. The vertical projection of a phasor at any instant gives the instantaneous value: v_m sin ωt for the voltage phasor V, i_m sin ωt for the current phasor I. For a resistor the two phasors point the same way at all times, showing a phase difference of zero.

Voltage and current are scalars, not vectors. Phasors are a bookkeeping device: sinusoids of the same frequency combine exactly as the projections of rotating arrows do, so we can add them with the vector rules we already know.

Reading a phasor diagram

  1. Draw each quantity as an arrow Length = amplitude; angle = phase at the chosen instant.
  2. Let the arrows rotate anticlockwise All at the same angular speed ω.
  3. Take vertical projections They give the instantaneous values v and i.
  4. Compare angles The arrow ahead (anticlockwise) leads; the one behind lags.

Worked example 1: a heater on the mains

A heater is rated 1000 W, 230 V. R = V²/P = 230² ÷ 1000 = 52 900 ÷ 1000 = 52.9 Ω. rms current I = P/V = 1000 ÷ 230 ≈ 4.35 A. Peak voltage = √2 × 230 ≈ 325 V; peak current = √2 × 4.35 ≈ 6.15 A.

Worked example 2: reading an equation

A current is i = 5 sin (100πt) A. Peak i_m = 5 A, so I = 5/√2 ≈ 3.54 A. 2πν = 100π gives ν = 50 Hz. In a 10 Ω resistor the average power is I²R = (5²/2) × 10 = 12.5 × 10 = 125 W, while the average current over a cycle is zero.

Worked example 3: from peak to rms

A supply has peak voltage 170 V. V = 170/√2 ≈ 120 V rms. A 60 Ω resistor on it draws I = 120 ÷ 60 = 2 A rms (peak 2.83 A) and dissipates 120 × 2 = 240 W.

Key takeaways

  • v = v_m sin ωt; in a resistor i = (v_m/R) sin ωt, in phase with v.
  • Average current over a cycle is zero, but average power is ½i_m²R.
  • rms values: I = i_m/√2, V = v_m/√2; then V = IR and P = VI = I²R.
  • Phasors are rotating arrows whose projections give instantaneous values.

Check your understanding

  1. 1. The peak voltage of an ac supply is 250 V. What is its rms voltage?

    1. 125 V
    2. 177 V
    3. 354 V
    4. 250 V
    Show answer

    Answer: B. V = v_m/√2 = 250 ÷ 1.414 ≈ 177 V.

  2. 2. A 50 Ω resistor is connected to a 230 V, 50 Hz supply. What is the average power consumed over a full cycle?

    1. 1058 W
    2. 4.6 W
    3. 2116 W
    4. Zero
    Show answer

    Answer: A. Using rms values, P = V²/R = 230² ÷ 50 = 52 900 ÷ 50 = 1058 W. The average current is zero, but the average power is not.

  3. 3. The rms value of a sinusoidal current is 6 A. What is its peak value?

    1. 4.24 A
    2. 6 A
    3. 12 A
    4. 8.49 A
    Show answer

    Answer: D. i_m = √2 × I = 1.414 × 6 ≈ 8.49 A.

  4. 4. In a purely resistive ac circuit, the phase difference between current and voltage is

    1. π/2
    2. π
    3. zero
    4. π/4
    Show answer

    Answer: C. v_m sin ωt = iR gives i = (v_m/R) sin ωt, so current and voltage reach their maxima together: the phase difference is zero.

  5. 5. Assertion (A): The average value of an alternating current over one full cycle is zero, yet it heats a resistor. Reason (R): The heating depends on the square of the current, which is never negative.

    1. Both A and R are true, and R is the correct explanation of A
    2. Both A and R are true, but R is not the correct explanation of A
    3. A is true, but R is false
    4. A is false, but R is true
    Show answer

    Answer: A. Both are true. Positive and negative halves of the current cancel in the average, but the power i²R is positive throughout, giving an average power ½i_m²R. R explains A.

Privacy · Terms · Refunds · Delivery