• Foundation
  • About 22 min
  • 5 practice questions

Series LCR circuit: impedance and phase

Use a phasor diagram to find the current in a series LCR circuit, derive the impedance Z = √(R² + (X_C − X_L)²) and the phase angle tan φ = (X_C − X_L)/R, and add voltages across elements correctly.

If something looks wrong, please tell us.

By the end of this lesson you can

  • Draw the phasor diagram for a series LCR circuit.
  • Derive the impedance Z and the phase angle φ.
  • Decide whether a circuit is inductive or capacitive and whether the current leads or lags.
  • Explain why voltages across series elements do not add as plain numbers.

Real circuits contain resistance, inductance and capacitance together. In a series LCR circuit the same current flows through all three, but each element's voltage has a different phase. Phasors let us combine them neatly.

Phasor-diagram solution

Let the source voltage be v = v_m sin ωt and the current be i = i_m sin (ωt + φ), where φ is the phase difference to be found. The loop rule is L di/dt + iR + q/C = v. Represent the current by the phasor I.

  1. V_R (amplitude i_mR) is parallel to I.
  2. V_L (amplitude i_mX_L) is π/2 ahead of I.
  3. V_C (amplitude i_mX_C) is π/2 behind I.
  4. So V_L and V_C point in opposite directions and combine into one phasor of length |i_mX_C − i_mX_L|.
  5. The source phasor V is the vector sum: V = V_R + V_L + V_C, the hypotenuse of a right triangle with sides i_mR and i_m(X_C − X_L).
  6. Pythagoras: v_m² = i_m²[R² + (X_C − X_L)²].

i_m = v_m/Z, with impedance Z = √[R² + (X_C − X_L)²] (ohm). Phase angle: tan φ = (X_C − X_L)/R.

The right triangle with sides R and (X_C − X_L) and hypotenuse Z is the impedance diagram. The power factor cos φ = R/Z will be used in the next lesson.

Reading the phase angle
ConditionSign of φCircuit behaves asCurrent
X_C > X_LPositiveCapacitiveLeads the source voltage
X_L > X_CNegativeInductiveLags the source voltage
X_L = X_CZeroPurely resistive (Z = R)In phase with the voltage (resonance)

Solving a series LCR problem

  1. Reactances X_L = ωL and X_C = 1/ωC at the given frequency.
  2. Impedance Z = √[R² + (X_C − X_L)²].
  3. Current I = V/Z (rms) or i_m = v_m/Z (peak).
  4. Phase tan φ = (X_C − X_L)/R; decide lead or lag.
  5. Element voltages V_R = IR, V_L = IX_L, V_C = IX_C; combine by phasors.

Steady state and transients. The phasor solution describes the steady state, after the circuit has settled. When a circuit is first switched on there is also a transient part that dies away; the phasor method says nothing about it or about initial conditions.

Worked example 1: a full LCR circuit

A series circuit has R = 30 Ω, X_L = 80 Ω and X_C = 40 Ω on a 250 V (rms) supply.

  1. Z = √[30² + (40 − 80)²] = √(900 + 1600) = √2500 = 50 Ω.
  2. I = V/Z = 250 ÷ 50 = 5 A.
  3. tan φ = (40 − 80)/30 = −4/3, so φ ≈ −53°: the circuit is inductive and the current lags the voltage by about 53°.
  4. V_R = 5 × 30 = 150 V, V_L = 5 × 80 = 400 V, V_C = 5 × 40 = 200 V.
  5. Check: √[150² + (400 − 200)²] = √(22 500 + 40 000) = 250 V, the source voltage.

Notice that V_L alone (400 V) is larger than the supply voltage. That is possible because V_L and V_C are opposite in phase and partly cancel.

Worked example 2: the RC 'paradox'

A 120 Ω resistor and a capacitor of reactance 160 Ω are in series on 200 V rms. Z = √(120² + 160²) = 200 Ω, so I = 1 A. V_R = 120 V and V_C = 160 V, which add to 280 V as plain numbers - more than the 200 V supply! The paradox disappears when phases are respected: V_R and V_C are 90° apart, so the total is √(120² + 160²) = 200 V. The current leads the voltage by φ = tan⁻¹(160/120) ≈ 53°.

Worked example 3: finding the inductance

A coil of resistance 40 Ω draws 2 A rms from a 200 V, 50 Hz supply. Z = 200 ÷ 2 = 100 Ω. X_L = √(Z² − R²) = √(10 000 − 1600) ≈ 91.7 Ω. L = X_L/(2πν) = 91.7 ÷ 314 ≈ 0.29 H.

Key takeaways

  • Same current through all series elements; their voltages differ in phase.
  • Z = √[R² + (X_C − X_L)²]; i_m = v_m/Z.
  • tan φ = (X_C − X_L)/R: positive φ (capacitive) means current leads; negative (inductive) means it lags.
  • Element voltages add as phasors, not as numbers.

Check your understanding

  1. 1. A series circuit has R = 6 Ω, X_L = 12 Ω and X_C = 4 Ω. What is its impedance?

    1. 22 Ω
    2. 10 Ω
    3. 14 Ω
    4. 8 Ω
    Show answer

    Answer: B. Z = √[R² + (X_C − X_L)²] = √[36 + (4 − 12)²] = √(36 + 64) = √100 = 10 Ω.

  2. 2. In the circuit of the previous question, the current

    1. leads the voltage, since X_C < X_L
    2. is in phase with the voltage
    3. leads the voltage by 90°
    4. lags the voltage, since X_L > X_C
    Show answer

    Answer: D. With X_L > X_C, tan φ = (X_C − X_L)/R is negative: the circuit is inductive and the current lags the source voltage (by tan⁻¹(8/6) ≈ 53°).

  3. 3. A 200 Ω resistor and a capacitor are in series on a 220 V supply. The rms voltage across the resistor is 132 V. What is the rms voltage across the capacitor?

    1. 88 V
    2. 176 V
    3. 352 V
    4. 220 V
    Show answer

    Answer: B. The voltages are 90° apart, so V² = V_R² + V_C². V_C = √(220² − 132²) = √(48 400 − 17 424) = √30 976 = 176 V.

  4. 4. For a series LCR circuit with X_L = X_C, the phase difference between current and voltage is

    1. zero
    2. π/2
    3. π/4
    4. π
    Show answer

    Answer: A. tan φ = (X_C − X_L)/R = 0, so φ = 0: the reactive voltages cancel and the circuit behaves as a pure resistance.

  5. 5. Assertion (A): In a series LCR circuit, the rms voltage across the inductor can be greater than the rms voltage of the source. Reason (R): The voltages across the inductor and the capacitor are opposite in phase and partly cancel.

    1. Both A and R are true, and R is the correct explanation of A
    2. Both A and R are true, but R is not the correct explanation of A
    3. A is true, but R is false
    4. A is false, but R is true
    Show answer

    Answer: A. Both are true. Because V_L and V_C are 180° apart, the source supplies only their difference (plus V_R in quadrature), so each of V_L or V_C can individually exceed the supply voltage. R explains A.

Sign in to keep track of the lessons you finish.

Next lesson → Resonance and power in ac circuits

Privacy · Terms · Refunds · Delivery