- Foundation
- About 22 min
- 5 practice questions
Resonance and power in ac circuits
Find the resonant frequency ω₀ = 1/√(LC) of a series LCR circuit, explain its use in tuning, and derive the average power P = VI cos φ, the meaning of power factor and wattless current.
If something looks wrong, please tell us.
By the end of this lesson you can
- Explain resonance in a series LCR circuit and derive ω₀ = 1/√(LC).
- Describe how the current varies with frequency and the role of R, and use Q = ω₀L/R.
- Derive the average power P = VI cos φ and interpret the power factor.
- Explain wattless current and why a low power factor is undesirable.
A child on a swing goes higher and higher if pushed in step with the swing's natural rhythm. An LCR circuit has a natural frequency too, and when driven at that frequency the current becomes as large as it can be. This resonance lets a radio pick out one station from hundreds.
Resonance
The current amplitude is i_m = v_m/√[R² + (X_C − X_L)²]. As ω changes, X_L = ωL rises and X_C = 1/ωC falls. At one particular frequency they become equal, Z is smallest (Z = R) and the current is largest.
Resonance: X_L = X_C, i.e. ω₀L = 1/(ω₀C), so ω₀ = 1/√(LC) and ν₀ = 1/(2π√(LC)). At resonance Z = R, i_m = v_m/R and φ = 0.
- Resonance needs both L and C: only then can their voltages cancel. An RL or RC circuit cannot resonate.
- A smaller R gives a taller, sharper peak in the current-versus-frequency graph; doubling R halves the peak current.
- The sharpness is described by the quality factor Q = ω₀L/R = 1/(ω₀CR): the larger Q, the sharper the resonance.
Tuning a radio. The aerial picks up signals from many stations at once, which drive the tuning circuit at many frequencies. Turning the tuning knob changes C until ω₀ matches the frequency of the wanted station; only that signal then produces a large current. A metal detector at an airport is also a tuned circuit: metal passing through its coil changes the impedance, and the resulting change in current sets off the alarm.
Worked example 1: a resonant circuit
L = 0.5 H, C = 20 μF and R = 10 Ω are in series with a 100 V (rms) variable-frequency source. ω₀ = 1/√(0.5 × 20 × 10⁻⁶) = 1/√(10⁻⁵) ≈ 316 rad s⁻¹, so ν₀ = 316 ÷ 2π ≈ 50 Hz. At resonance Z = R = 10 Ω, I = 100 ÷ 10 = 10 A, and Q = ω₀L/R = 316 × 0.5 ÷ 10 ≈ 16. Then V_L = IX_L = 10 × 158 = 1580 V and V_C is the same - each far larger than the 100 V supply, while they cancel each other.
Power in an ac circuit
With v = v_m sin ωt and i = i_m sin (ωt + φ), the instantaneous power is p = v_m i_m sin ωt sin (ωt + φ) = (v_m i_m/2)[cos φ − cos (2ωt + φ)]. The second term averages to zero over a cycle, so:
P = (v_m i_m/2) cos φ = V I cos φ = I²Z cos φ. The factor cos φ is the power factor; for a series LCR circuit cos φ = R/Z.
| Circuit | φ | Power factor | Average power |
|---|---|---|---|
| Pure resistor | 0 | 1 | Maximum, VI |
| Pure L or pure C | ±π/2 | 0 | Zero (wattless current) |
| RL, RC or LCR | Between | R/Z | I²R - dissipated only in R |
| LCR at resonance | 0 | 1 | Maximum, I²R with I = V/R |
A current that flows without any average power being consumed - as in a pure inductor or capacitor - is called a wattless current. In general the current can be split into a component in phase with the voltage (the power component, I cos φ) and one at 90° to it (the wattless component, I sin φ).
Why a low power factor is costly. To deliver power P at voltage V, the current needed is I = P/(V cos φ). A small cos φ means a large current and so large I²R losses in transmission lines. Many loads (motors, for example) are inductive, with current lagging the voltage. Connecting a suitable capacitor in parallel supplies a leading wattless current that cancels the lagging one, bringing cos φ close to 1.
Improving a low power factor
- Inductive load Current lags the voltage; it has a large wattless component.
- Add a capacitor in parallel It draws a leading wattless current.
- Wattless parts cancel Only the power component, in phase with V, remains.
- Result cos φ → 1, smaller line current, smaller transmission loss.
Worked example 2: power and power factor
For the circuit of the last lesson (R = 30 Ω, Z = 50 Ω, V = 250 V, I = 5 A): cos φ = R/Z = 30 ÷ 50 = 0.6. P = VI cos φ = 250 × 5 × 0.6 = 750 W. Check: I²R = 25 × 30 = 750 W - all the power is dissipated in the resistor.
Worked example 3: tuning to a station
A tuning circuit has a 200 μH coil. What capacitance tunes it to 1.0 MHz? C = 1/(ω₀²L) with ω₀ = 2π × 10⁶ ≈ 6.28 × 10⁶ rad s⁻¹. ω₀² ≈ 3.95 × 10¹³, so C = 1 ÷ (3.95 × 10¹³ × 2 × 10⁻⁴) ≈ 1.27 × 10⁻¹⁰ F ≈ 127 pF.
Key takeaways
- Resonance: X_L = X_C, ω₀ = 1/√(LC); Z = R and current is maximum; needs both L and C.
- Q = ω₀L/R measures sharpness; tuning a radio varies C to set ω₀.
- P = VI cos φ; power factor cos φ = R/Z; only R dissipates power.
- Wattless current: cos φ = 0; a low power factor raises transmission losses, and a parallel capacitor can improve it.
Check your understanding
-
1. What is the resonant angular frequency of a series circuit with L = 2 mH and C = 5 μF?
- 1 × 10⁴ rad s⁻¹
- 1 × 10⁸ rad s⁻¹
- 1.6 × 10³ rad s⁻¹
- 1 × 10⁵ rad s⁻¹
Show answer
Answer: A. ω₀ = 1/√(LC) = 1/√(2 × 10⁻³ × 5 × 10⁻⁶) = 1/√(10⁻⁸) = 10⁴ rad s⁻¹.
-
2. A series LCR circuit with R = 25 Ω is connected to a variable-frequency 230 V supply. What average power does it take at resonance?
- 230 W
- 9.2 W
- 2116 W
- 4232 W
Show answer
Answer: C. At resonance Z = R, so I = 230 ÷ 25 = 9.2 A and P = I²R = 84.64 × 25 = 2116 W (the same as V²/R).
-
3. The power factor of a series circuit with R = 8 Ω and Z = 10 Ω is
- 1.25
- 0.6
- 0.2
- 0.8
Show answer
Answer: D. cos φ = R/Z = 8 ÷ 10 = 0.8.
-
4. Which circuit can show resonance?
- A series R-C circuit
- A series L-C-R circuit
- A series R-L circuit
- A pure resistor
Show answer
Answer: B. Resonance needs the inductive and capacitive voltages to cancel, so both L and C must be present. RL and RC circuits have no frequency at which the reactance vanishes.
-
5. Assertion (A): For a given power at a given voltage, a load with a low power factor needs a larger current. Reason (R): Average power P = VI cos φ.
- Both A and R are true, and R is the correct explanation of A
- Both A and R are true, but R is not the correct explanation of A
- A is true, but R is false
- A is false, but R is true
Show answer
Answer: A. Both are true. From P = VI cos φ, I = P/(V cos φ); a smaller cos φ means a larger I, and hence larger I²R losses in the supply lines. R explains A.
Sign in to keep track of the lessons you finish.