- Foundation
- About 26 min
- 5 practice questions
Diode characteristics, rectifiers and filters
Interpret the V-I characteristics of a junction diode, calculate dynamic resistance, and explain half-wave and full-wave rectifiers and capacitor filters.
If something looks wrong, please tell us.
By the end of this lesson you can
- Describe the circuits used to plot a diode's V-I characteristics.
- Identify threshold voltage, reverse saturation current and breakdown on the graph.
- Calculate dynamic resistance r_d = ΔV/ΔI.
- Explain half-wave and full-wave rectification and the action of a capacitor filter.
The mains supply is alternating current, but phones, laptops and most electronics need steady direct current. The diode's one-way behaviour turns ac into dc. To use a diode well we first need its V-I characteristic: how its current depends on the voltage across it.
Measuring the characteristic
A battery feeds the diode through a potentiometer (or rheostat) so the voltage across it can be varied. For forward bias a milliammeter is used, because the current is large; for reverse bias the battery is reversed and a microammeter is used, because the current is tiny. The current is noted for each voltage and a graph of I against V is drawn.
Reading the V-I graph
- Forward bias: the current stays almost zero until the voltage passes the threshold (cut-in) voltage, about 0.7 V for silicon and 0.2 V for germanium. Beyond it the current rises steeply (exponentially) for tiny increases in voltage.
- Reverse bias: the current is very small (microamperes) and nearly constant: the reverse saturation current.
- Breakdown: at a large reverse voltage the current suddenly increases. Ordinary diodes are not used in this region.
So the diode's resistance is low in forward bias and very high in reverse bias. Because the graph is curved, resistance is defined for small changes around a working point: the dynamic resistance:
Dynamic resistance r_d = ΔV/ΔI. Low (a few ohms) in forward bias above threshold; very high (megohms or more) in reverse bias.
Worked example 1: dynamic resistance
On the forward characteristic of a silicon diode, the current is 5 mA at 0.70 V and 15 mA at 0.75 V. r_d = ΔV/ΔI = (0.75 − 0.70)/(15 − 5) × 10⁻³ = 0.05/0.010 = 5 Ω. In reverse bias the same diode carries 2 μA at −20 V, so its reverse resistance is about 20/(2 × 10⁻⁶) = 1 × 10⁷ Ω, two million times larger.
Half-wave rectifier
The secondary of a transformer applies an ac voltage across a diode in series with a load resistor R_L. In the half-cycle when the diode's p-side is positive, it is forward biased, conducts, and a voltage appears across R_L. In the other half-cycle the diode is reverse biased and (its reverse current being negligible) no current flows. The output is a series of half-sine pulses, all in one direction. The diode's reverse breakdown voltage must be well above the peak ac voltage, or the diode would break down in the blocking half-cycle.
Full-wave rectifier (centre-tap)
Full-wave rectification with a centre-tap transformer
- Centre-tap secondary Ends A and B are always in opposite phase relative to the centre tap.
- First half-cycle: A positive Diode D₁ is forward biased and conducts; D₂ is reverse biased.
- Second half-cycle: B positive Diode D₂ conducts; D₁ is reverse biased.
- Same direction through R_L Both diodes send current the same way through the load.
- Output A pulse in every half-cycle: full-wave rectified voltage.
The p-sides of two diodes connect to the two ends of the transformer secondary, their n-sides join together, and the output is taken between this common point and the centre tap of the secondary. Each diode rectifies only half of the total secondary voltage, and each conducts in alternate half-cycles, so the load gets current in both halves. This is more efficient than the half-wave circuit. (Another full-wave circuit, the bridge, uses four diodes and needs no centre tap.)
| Rectifier | Diodes | Output pulses per input cycle | Output ripple frequency for 50 Hz input |
|---|---|---|---|
| Half-wave | 1 | 1 | 50 Hz |
| Full-wave (centre tap) | 2 | 2 | 100 Hz |
Filters: smoothing the output
Rectified output is one-directional but still pulsating. To get steady dc, a filter is added: usually a large capacitor connected across the load (in parallel with R_L), or an inductor in series with R_L. The capacitor charges up to the peak voltage as each pulse rises. As the pulse falls, it discharges slowly through R_L, keeping the voltage up, until the next pulse recharges it. The rate of fall depends inversely on the time constant R_LC. A large capacitor gives a large time constant, so the output stays close to the peak voltage with only a small ripple. This capacitor input filter is the most widely used in power supplies.
Worked example 2: is the filter good enough?
A full-wave rectifier with 50 Hz input feeds a 1.0 kΩ load with a 470 μF capacitor. The pulses come at 100 Hz, so the capacitor must hold up the voltage for about 1/100 s = 0.01 s between pulses. Time constant R_LC = 1.0 × 10³ × 470 × 10⁻⁶ = 0.47 s. Since 0.47 s is about 47 times longer than the 0.01 s gap, the capacitor loses only a small fraction of its charge between pulses: the output is a nearly steady dc with a small ripple.
Worked example 3: output frequency
If the input is 60 Hz ac, a half-wave rectifier gives 60 output pulses per second (ripple frequency 60 Hz), while a full-wave rectifier gives 120 pulses per second (120 Hz), which is easier to smooth.
Key takeaways
- Forward current rises steeply above the threshold voltage (about 0.7 V for Si, 0.2 V for Ge); reverse current is tiny until breakdown.
- Dynamic resistance r_d = ΔV/ΔI is low in forward bias and very high in reverse.
- Half-wave rectifiers use one diode; full-wave (centre-tap) use two and give double the ripple frequency.
- A capacitor filter with a large R_LC gives nearly steady dc.
Check your understanding
-
1. The threshold (cut-in) voltage of a silicon diode is about
- 0.2 V
- 1.1 V
- 0.7 V
- 5 V
Show answer
Answer: C. A silicon diode conducts appreciably only above about 0.7 V; germanium needs only about 0.2 V.
-
2. On a diode's forward characteristic, the current rises from 10 mA to 30 mA when the voltage rises from 0.72 V to 0.82 V. The dynamic resistance is
- 5 Ω
- 2.7 Ω
- 27 Ω
- 50 Ω
Show answer
Answer: A. r_d = ΔV/ΔI = (0.82 − 0.72)/(30 − 10) × 10⁻³ = 0.10/0.020 = 5 Ω.
-
3. A rectifier works from 50 Hz mains, and its unfiltered output shows 100 pulses every second. The rectifier is
- a half-wave rectifier with one diode
- not rectifying at all
- a half-wave rectifier with a capacitor filter
- a full-wave rectifier
Show answer
Answer: D. A half-wave rectifier gives one pulse per input cycle (50 per second). Getting 100 pulses per second means a pulse in every half-cycle, which is full-wave rectification.
-
4. In a capacitor filter, the output voltage is smoother when
- the capacitance is small
- the load resistance is very small
- the product R_LC is large
- the capacitor is in series with the load
Show answer
Answer: C. A large time constant R_LC means the capacitor discharges only slightly between pulses, so the output stays close to the peak with little ripple. The capacitor goes in parallel with the load.
-
5. Assertion (A): A full-wave rectifier with a centre-tap transformer gives output in both half-cycles of the input. Reason (R): In each half-cycle one diode is forward biased while the other is reverse biased, and both send current the same way through the load.
- Both A and R are true, and R is the correct explanation of A
- Both A and R are true, but R is not the correct explanation of A
- A is true, but R is false
- A is false, but R is true
Show answer
Answer: A. Both are true. The two ends of the secondary are in opposite phase, so D₁ conducts in one half-cycle and D₂ in the other, each driving current in the same direction through R_L. R explains A.
Sign in to keep track of the lessons you finish.