- Foundation
- About 22 min
- 5 practice questions
Why semiconductors: classifying solids by conductivity and energy bands
Compare vacuum tubes with semiconductor devices, classify solids as metals, semiconductors and insulators by resistivity and by energy bands, and relate the band gap to conduction.
If something looks wrong, please tell us.
By the end of this lesson you can
- Explain why semiconductor devices replaced vacuum tubes.
- Classify solids by resistivity and conductivity.
- Describe valence band, conduction band and band gap.
- Distinguish metals, insulators and semiconductors using energy bands.
Every phone, computer and television is built from devices in which the flow of electrons is controlled. Before the transistor arrived in 1948, this control came from vacuum tubes (valves): a heated cathode gave off electrons that crossed an evacuated space to an anode, steered by the voltages on other electrodes (diode, triode, tetrode, pentode). Tubes were bulky, used a lot of power, needed high voltages (about 100 V), wore out and were not very reliable.
From the 1930s it became clear that certain solids, semiconductors, and the junctions between them could control both the number and the direction of moving charges, with simple triggers like light, heat or a small voltage. Here the charges are supplied and move inside the solid itself, with no heating and no vacuum. Semiconductor devices are small, use little power, run at low voltage, last long and are reliable. Even before this was understood, a natural crystal of galena (lead sulphide, PbS) touched by a metal point was used to detect radio waves.
Classification by resistivity
| Class | Resistivity ρ (Ω m) | Conductivity σ (S m⁻¹) |
|---|---|---|
| Metals | 10⁻² to 10⁻⁸ | 10² to 10⁸ |
| Semiconductors | 10⁻⁵ to 10⁶ | 10⁵ to 10⁻⁶ |
| Insulators | 10¹¹ to 10¹⁹ | 10⁻¹¹ to 10⁻¹⁹ |
Resistivity alone is not enough to tell the classes apart; the deeper difference lies in their energy bands. Semiconductors may be elemental (silicon, Si, and germanium, Ge) or compound: inorganic (CdS, GaAs, CdSe, InP), organic (anthracene, doped phthalocyanines) or organic polymers (polypyrrole, polyaniline, polythiophene). Most devices use Si, Ge and inorganic compounds; this chapter concentrates on Si and Ge.
Energy bands
In an isolated atom each electron has a sharp energy level. In a solid the atoms are so close that the outer orbits of neighbours overlap, and each electron sees a slightly different pattern of surrounding charges. The sharp levels spread into energy bands: groups of very closely spaced levels that behave as a continuous range of energy.
- The valence band contains the energy levels of the valence electrons.
- The conduction band lies above it. Electrons in the conduction band are free to move through the solid and carry current.
- The gap between the top of the valence band (E_V) and the bottom of the conduction band (E_C) is the band gap E_g; no electron energies are allowed inside it.
In a crystal of N silicon or germanium atoms, each atom has 4 outer electrons, so there are 4N valence electrons, while the outer shell offers 8N states. At the spacing of atoms in Si and Ge these 8N states split into two bands of 4N states each, separated by E_g. At absolute zero the lower band (valence band) is completely filled by the 4N electrons and the upper band (conduction band) is completely empty.
Energy bands in the three classes of solids
-
Metals
- Conduction and valence bands overlap, or the conduction band is partly filled
- E_g ≈ 0
- Many free electrons: very high conductivity
-
Insulators
- Large band gap, E_g > 3 eV
- Heat cannot lift electrons across
- No conduction electrons: no current
-
Semiconductors
- Small band gap, E_g < 3 eV
- At room temperature a few electrons cross the gap
- Moderate conductivity that rises with temperature
| Element (group 14) | Band gap E_g | Behaviour |
|---|---|---|
| Carbon (diamond) | 5.4 eV | Insulator |
| Silicon | 1.1 eV | Semiconductor |
| Germanium | 0.7 eV | Semiconductor |
| Tin | 0 eV | Metal |
Worked example 1: light that can free an electron
What is the longest wavelength of light that can lift an electron across the band gap of silicon (1.1 eV)? Photon energy must be at least E_g, so λ_max = hc/E_g. Using hc ≈ 1240 eV nm: λ_max = 1240/1.1 ≈ 1130 nm (infrared). Visible light (400–750 nm) has more than enough energy, which is why silicon solar cells work in sunlight. For diamond (5.4 eV), λ_max = 1240/5.4 ≈ 230 nm, ultraviolet: visible light passes through diamond without exciting electrons.
Worked example 2: classify by resistivity
Three samples have resistivities of (a) 2 × 10⁻⁸ Ω m, (b) 6 × 10² Ω m and (c) 10¹⁵ Ω m. Comparing with the table: (a) is a metal (like copper), (b) lies in the semiconductor range, and (c) is an insulator. The conductivities are σ = 1/ρ: (a) 5 × 10⁷ S m⁻¹, (b) about 1.7 × 10⁻³ S m⁻¹, (c) 10⁻¹⁵ S m⁻¹.
Metals: bands overlap (E_g ≈ 0). Semiconductors: 0 < E_g < 3 eV. Insulators: E_g > 3 eV. Diamond 5.4 eV, Si 1.1 eV, Ge 0.7 eV.
Key takeaways
- Semiconductor devices are small, efficient, low-voltage and reliable compared with vacuum tubes.
- Solids are classed by resistivity, but more deeply by their band structure.
- Conduction needs electrons in the conduction band (or vacancies in the valence band).
- The band gap decides whether a material is a metal, semiconductor or insulator.
Check your understanding
-
1. A material has a band gap of 5.4 eV. At room temperature it behaves as
- a metal
- an insulator
- a semiconductor
- a superconductor
Show answer
Answer: B. A band gap greater than about 3 eV is too large for thermal energy to lift electrons into the conduction band, so the material is an insulator. 5.4 eV is the gap of diamond.
-
2. In a metal, the valence band and the conduction band
- are separated by about 1 eV
- are separated by more than 3 eV
- overlap, or the conduction band is partly filled
- are both completely empty
Show answer
Answer: C. In metals the bands overlap (or the conduction band is partly filled), so many electrons are free to move with no energy gap to cross.
-
3. The longest wavelength of light that can create an electron-hole pair in germanium (E_g = 0.7 eV) is about (hc ≈ 1240 eV nm)
- 620 nm
- 870 nm
- 177 nm
- 1770 nm
Show answer
Answer: D. λ_max = hc/E_g = 1240/0.7 ≈ 1770 nm. Any longer wavelength carries less than 0.7 eV per photon.
-
4. Which is NOT an advantage of semiconductor devices over vacuum tubes?
- Small size
- Low operating voltage
- No heated cathode needed
- Electrons travel through a vacuum
Show answer
Answer: D. In semiconductor devices the charges move inside the solid, with no vacuum and no heating. Travel through a vacuum describes vacuum tubes, not semiconductor devices.
-
5. Assertion (A): Pure germanium conducts better than pure silicon at room temperature. Reason (R): The band gap of germanium (about 0.7 eV) is smaller than that of silicon (about 1.1 eV).
- Both A and R are true, and R is the correct explanation of A
- Both A and R are true, but R is not the correct explanation of A
- A is true, but R is false
- A is false, but R is true
Show answer
Answer: A. Both are true. With a smaller gap, thermal energy lifts more electrons into the conduction band of germanium, so it has more charge carriers and higher conductivity. R explains A.
Sign in to keep track of the lessons you finish.