• Practice
  • About 14 min
  • 5 practice questions

Preparing, diluting and mixing solutions: four question types and their traps

Solve the four standard preparation questions: mass for a given molarity, volume of stock needed, mixing solutions, and mixing by percent, including serial dilution.

If something looks wrong, please tell us.

Preparation questions are short and appear in almost every paper, so errors here cost easy marks. They fall into four types, and each has one trap. The numbers in this lesson are illustrative practice values, not data about any particular chemical supplier's product. Work each type through once and the pattern becomes automatic.

Type 1: mass of solute for a given molarity

Moles needed = M × V (V in litres), then mass = moles × molar mass. The trap is the volume unit: 250 mL is 0.250 L. To prepare 250 mL of 0.2 M NaOH (40 g/mol): moles = 0.2 × 0.250 = 0.050 mol; mass = 0.050 × 40 = 2.0 g. A student who uses 1 L gets 8 g, which is a typical wrong option. The 2.0 g is dissolved and the solution is made up to the 250 mL mark, not dissolved in 250 mL of water.

Type 2: volume of stock for dilution

Use M1V1 = M2V2 and solve for V1. Suppose a stock is 12 M (an illustrative strength) and you need 250 mL of 0.6 M. V1 = M2V2 ÷ M1 = 0.6 × 250 ÷ 12 = 12.5 mL. Take 12.5 mL of stock and add water up to 250 mL. The trap is calling 250 mL the water to be added; the water added is 250 − 12.5 = 237.5 mL only if volumes are additive, which is why the instruction is always 'make up to the mark'.

Type 3: mixing solutions of the same solute

Add the moles and divide by the total volume. 150 mL of 0.4 M and 350 mL of 0.2 M (volumes additive): moles = 0.4 × 0.150 + 0.2 × 0.350 = 0.060 + 0.070 = 0.130 mol in 0.500 L, so M = 0.26 M. The trap is the plain average (0.4 + 0.2) ÷ 2 = 0.3 M, which is correct only for equal volumes. The answer must lie between 0.2 and 0.4 and be nearer to 0.2, because more of the 0.2 M solution was used. That check alone eliminates the wrong options.

Type 4: mixing by percent to get a target

How much of a 20% solution and a 5% solution give 600 g of 10% solution? Use the cross method. Share of the strong solution is proportional to (target − weak) = 10 − 5 = 5. Share of the weak one is proportional to (strong − target) = 20 − 10 = 10. Ratio strong : weak = 5 : 10 = 1 : 2. So the strong solution is 600 ÷ 3 = 200 g and the weak is 400 g. Check the solute: 0.20 × 200 + 0.05 × 400 = 40 + 20 = 60 g, which is 10% of 600 g.

Serial dilution

In serial dilution each step multiplies the dilution factor. If 10 mL of a 1.0 M solution is made up to 100 mL (factor 10), and then 10 mL of that is made up to 100 mL again (factor 10), the final molarity is 1.0 ÷ (10 × 10) = 0.010 M. The method is used to prepare very dilute solutions accurately, because measuring a tiny mass directly is difficult.

Four types at a glance
TypeMethodTrap
Mass for a molaritymol = M × V(L); mass = mol × M(r)mL not converted to L
Stock volumeV1 = M2V2 ÷ M1Treating V2 as the water added
Mixing the same soluteAdd moles, divide by total volumeAveraging unequal volumes
Mixing by percentCross method, check the soluteDividing by solvent mass

Moles are what add and what stay fixed. Concentrations never add. Check that a mixture's value lies between the two ingredients and nearer the larger portion.

Key takeaways

  • Convert mL to L before using molarity.
  • M1V1 = M2V2 for dilution; V2 is the final volume.
  • Mixing: total moles ÷ total volume, never the plain average unless the volumes are equal.
  • Serial dilution multiplies the dilution factors.

Check your understanding

  1. 1. What mass of NaOH (40 g/mol) is needed to prepare 250 mL of 0.2 M solution?

    1. 8.0 g
    2. 2.0 g
    3. 0.50 g
    4. 20 g
    Show answer

    Answer: B. Moles = 0.2 × 0.250 = 0.050 mol; mass = 0.050 × 40 = 2.0 g. Using 1 L would give the trap value 8.0 g.

  2. 2. A stock solution is 12 M. What volume of stock is needed to prepare 250 mL of 0.6 M solution?

    1. 25 mL
    2. 5.0 mL
    3. 125 mL
    4. 12.5 mL
    Show answer

    Answer: D. V1 = M2V2 ÷ M1 = 0.6 × 250 ÷ 12 = 12.5 mL.

  3. 3. 150 mL of 0.4 M solution is mixed with 350 mL of 0.2 M solution of the same solute (volumes additive). The final molarity is:

    1. 0.30 M
    2. 0.26 M
    3. 0.60 M
    4. 0.13 M
    Show answer

    Answer: B. Moles = 0.060 + 0.070 = 0.130 mol; volume = 0.500 L; M = 0.26 M. The plain average 0.30 M ignores the different volumes.

  4. 4. What mass of 20% solution must be mixed with a 5% solution to obtain 600 g of a 10% solution?

    1. 200 g
    2. 400 g
    3. 300 g
    4. 100 g
    Show answer

    Answer: A. Cross method: strong : weak = (10 − 5) : (20 − 10) = 1 : 2, so the 20% solution is 600 ÷ 3 = 200 g.

  5. 5. 10 mL of 1.0 M solution is made up to 100 mL; then 10 mL of this is again made up to 100 mL. The final molarity is:

    1. 0.10 M
    2. 0.20 M
    3. 0.001 M
    4. 0.010 M
    Show answer

    Answer: D. Each step dilutes by a factor of 10, so the total factor is 100 and M = 1.0 ÷ 100 = 0.010 M.

Privacy · Terms · Refunds · Delivery