• Practice
  • About 14 min
  • 5 practice questions

Pressure on solids: contact area, stacked blocks and the traps

Solve exam-style problems on the pressure that solid objects exert, using faces, stacks, uniform columns and careful unit conversion.

If something looks wrong, please tell us.

Problems on the pressure exerted by solids look easy because there is only one formula, P = F/A. Yet this is where many marks are lost, through the wrong area, the wrong unit or the wrong force. This lesson gives you a method and the traps to watch. Take g = 10 m/s² throughout.

A four-step method

  1. Find the force that presses on the surface. On a horizontal surface this is the weight, W = mg, of everything resting on that surface.
  2. Find the area that is actually in contact with the surface, not the total surface area of the object.
  3. Convert everything to SI units: kg, m, m², N. Remember 1 cm² = 10⁻⁴ m² and 1 mm² = 10⁻⁶ m².
  4. Divide: P = F/A, and give the answer in pascal (N/m²).

Worked examples

Example 1: the three faces of a block. A solid block measures 0.4 m × 0.2 m × 0.1 m and has a mass of 24 kg, so its weight is 240 N. Resting on its largest face (0.4 × 0.2 = 0.08 m²): P = 240 ÷ 0.08 = 3000 Pa. On its medium face (0.4 × 0.1 = 0.04 m²): P = 240 ÷ 0.04 = 6000 Pa. On its smallest face (0.2 × 0.1 = 0.02 m²): P = 240 ÷ 0.02 = 12 000 Pa. The weight is the same in all three cases; only the area changes, so the pressure is four times as great on the smallest face as on the largest.

Example 2: a uniform column. A solid cylinder of density 2700 kg/m³ and height 0.3 m stands on its flat base. Its weight is W = ρVg = ρ(A × h)g. So P = W/A = ρgh = 2700 × 10 × 0.3 = 8100 Pa. The base area cancelled, so a thick cylinder and a thin one of the same material and height press equally on the ground. This is a very useful shortcut for any uniform, straight-sided solid standing on its base.

Example 3: stacked blocks. A block A of mass 10 kg rests on a block B of mass 20 kg, which rests on the floor. The base of A is 0.05 m² and the base of B is 0.1 m². Pressure of A on B = 100 ÷ 0.05 = 2000 Pa. The force on the floor is the weight of both, 300 N, so the pressure on the floor = 300 ÷ 0.1 = 3000 Pa. The contact area for the floor is the base of B only.

Example 4: wide tyres. A tractor of mass 3000 kg has four tyres, each with 0.25 m² touching the ground. Total area = 1 m², so P = 30 000 ÷ 1 = 30 000 Pa. If narrow wheels of 0.05 m² each were fitted, the area would be 0.2 m² and P = 30 000 ÷ 0.2 = 150 000 Pa, five times larger. This is why heavy vehicles on soft ground use wide tyres or tracks.

Example 5: force from pressure. The air inside a closed tank exerts a gauge pressure of 2 × 10⁵ Pa on a circular lid of area 150 cm². Convert first: 150 cm² = 150 × 10⁻⁴ = 0.015 m². Force = P × A = 2 × 10⁵ × 0.015 = 3000 N. Had the area been left in cm², the answer would be wrong by a factor of 10 000.

Uniform solid standing on its base: P = ρgh, independent of base area. Otherwise P = (total weight above) ÷ (area of contact).

— Rule to remember

Common traps

  • Using the total surface area of a brick instead of the face it rests on.
  • Using mass in kg in place of weight in newton. Multiply by g first.
  • Forgetting to convert cm² to m² before dividing.
  • Adding the weights of blocks when asked for the pressure between two upper blocks. Only the weight above that contact counts.
  • Thinking a tilted object has the same area in contact. If an object is tilted so that it rests on an edge, the area is far smaller and the pressure far larger.

Key takeaways

  • The same weight on a smaller area gives a greater pressure; compare faces by their areas.
  • For a uniform column, P = ρgh; the area drops out.
  • Choose the force and the area for the same contact surface.
  • Always convert to m² before using P = F/A.

Check your understanding

  1. 1. A block of weight 120 N rests on a face of area 0.06 m². Its pressure on the table is:

    1. 1000 Pa
    2. 2000 Pa
    3. 7200 Pa
    4. 20 000 Pa
    Show answer

    Answer: B. P = F/A = 120 ÷ 0.06 = 2000 Pa.

  2. 2. A uniform iron bar of density 7800 kg/m³ and height 0.5 m stands on its base. Taking g = 10 m/s², the pressure on the floor is:

    1. 3900 Pa
    2. 7800 Pa
    3. 39 000 Pa
    4. 78 000 Pa
    Show answer

    Answer: C. For a uniform column P = ρgh = 7800 × 10 × 0.5 = 39 000 Pa. The base area is not needed.

  3. 3. A brick of weight 30 N has faces of 0.06 m², 0.03 m² and 0.02 m². The greatest pressure it can exert is:

    1. 500 Pa
    2. 1000 Pa
    3. 1500 Pa
    4. 3000 Pa
    Show answer

    Answer: C. The greatest pressure comes from the smallest face: 30 ÷ 0.02 = 1500 Pa. The other faces give 500 Pa and 1000 Pa.

  4. 4. A force of 600 N acts perpendicular to a surface of area 200 cm². The pressure is:

    1. 3 Pa
    2. 30 000 Pa
    3. 3000 Pa
    4. 300 000 Pa
    Show answer

    Answer: B. 200 cm² = 200 × 10⁻⁴ = 0.02 m². P = 600 ÷ 0.02 = 30 000 Pa.

  5. 5. A 40 kg block rests on a 60 kg block. The lower block has a base area of 0.5 m². The pressure on the floor is:

    1. 800 Pa
    2. 1200 Pa
    3. 2000 Pa
    4. 200 Pa
    Show answer

    Answer: C. Force on the floor = (40 + 60) × 10 = 1000 N. P = 1000 ÷ 0.5 = 2000 Pa.

Privacy · Terms · Refunds · Delivery