• Foundation
  • About 13 min
  • 5 practice questions

Friction and efficiency: why machines lose energy and how to reduce it

Explain where a machine loses energy, compare the effort with and without friction, and calculate the benefit of lubrication.

If something looks wrong, please tell us.

A real machine never gives out all the work it takes in. The missing energy has not vanished. It has become heat and sound. This lesson looks at why that happens, how efficiency measures it, and what can be done about it. The values used are illustrative.

Where does the energy go?

  • Friction at axles, hinges and pulley bearings, where surfaces rub. The work done against friction becomes heat.
  • The weight of the moving parts. In a pulley system the movable pulley must also be lifted.
  • Stiffness of ropes and belts, which have to bend round wheels.
  • Sound and vibration from loose or worn parts.

Improving a machine

  • Lubrication: oil or grease between moving surfaces lowers friction.
  • Ball bearings and rollers: rolling friction is much smaller than sliding friction.
  • Lighter moving parts, so less energy is spent moving the machine itself.
  • Cleaning and tightening so that parts do not rub or rattle.

Friction is not always unwanted. It lets a screw hold a board, a belt grip a wheel, and brakes stop a bicycle. The aim is less friction where parts must slide, and more where they must grip.

Worked examples

Example 1: the ramp. A 500 N drum is pushed up a ramp 5 m long and 1 m high. Without friction the effort would be 500 × 1 ÷ 5 = 100 N. With friction an effort of 150 N is needed. Work in = 150 × 5 = 750 J. Work out = 500 × 1 = 500 J. Efficiency = 500 ÷ 750 = 66.7%. This also equals ideal effort ÷ actual effort = 100 ÷ 150. Energy wasted = 250 J.

Example 2: oiling a pulley system. A pulley system with VR = 4 lifts a load of 700 N. When it is dry its efficiency is 70%, so MA = 0.7 × 4 = 2.8 and the effort = 700 ÷ 2.8 = 250 N. After oiling, the efficiency rises to 85%, MA = 0.85 × 4 = 3.4, and the effort = 700 ÷ 3.4 = 205.9 N, which is about 206 N. Oiling saves roughly 44 N of effort.

Example 3: two machines in a chain. A hand-winch of efficiency 90% drives a pulley system of efficiency 80%. The overall efficiency = 0.9 × 0.8 = 0.72 = 72%. Each stage loses some energy, so the more stages there are, the lower the overall efficiency.

Example 4: energy accounting. A machine takes in 500 J. It gives out 400 J of useful work. The loss is 100 J, shown as heat in the bearings. Efficiency = 400 ÷ 500 = 80%. If we could somehow halve the losses to 50 J, the efficiency would rise to 450 ÷ 500 = 90%, but it could never reach 100%.

Efficiency = useful work out ÷ work in × 100%. The energy lost is turned into heat, sound and the energy of moving the machine's own parts.

— Rule to remember

Key takeaways

  • Friction turns useful energy into heat.
  • Lubrication, bearings and lighter parts raise efficiency.
  • Efficiency of a chain of machines is the product of the efficiencies.
  • No machine is 100% efficient.

Check your understanding

  1. 1. The energy that a machine loses to friction is changed mainly into:

    1. Heat
    2. Light
    3. Gravitational energy of the load
    4. Mass
    Show answer

    Answer: A. Work done against friction appears as heat (and a little sound), so bearings warm up during use.

  2. 2. Oiling the axle of a pulley will:

    1. Increase friction
    2. Decrease the load
    3. Lower the friction
    4. Raise the velocity ratio
    Show answer

    Answer: C. Oil lowers the friction between moving surfaces, so less energy is wasted and the efficiency rises.

  3. 3. A ramp needs an actual effort of 160 N, while the ideal effort is 120 N. The efficiency is:

    1. 133%
    2. 75%
    3. 25%
    4. 80%
    Show answer

    Answer: B. Efficiency = ideal effort ÷ actual effort = 120 ÷ 160 = 0.75 = 75%.

  4. 4. Two machines of efficiency 50% and 80% are used one after the other. The overall efficiency is:

    1. 65%
    2. 130%
    3. 30%
    4. 40%
    Show answer

    Answer: D. The efficiencies multiply: 0.5 × 0.8 = 0.4 = 40%.

  5. 5. In which case is friction helpful?

    1. The hinge of a door
    2. The axle of a bicycle wheel
    3. The grip of a screw in wood
    4. The bearings of a fan
    Show answer

    Answer: C. Friction holds a screw in wood. In hinges, axles and bearings it is unwanted and is reduced with oil or ball bearings.

Sign in to keep track of the lessons you finish.

Next lesson → Final self-assessment: simple machines

Privacy · Terms · Refunds · Delivery