• Practice
  • About 25 min
  • 5 practice questions

Critical constants, Andrews' isotherms and liquefaction of gases

Interpret Andrews' isotherms of carbon dioxide, define and derive the critical constants Vc = 3b, Pc = a/27b² and Tc = 8a/27Rb, explain the Joule-Thomson effect and inversion temperature, and describe methods of liquefying gases.

If something looks wrong, please tell us.

By the end of this lesson you can

  • Describe Andrews' P-V isotherms of carbon dioxide and locate the critical point.
  • Define critical temperature, critical pressure and critical volume.
  • Derive Vc = 3b, Pc = a/27b² and Tc = 8a/27Rb from the van der Waals equation and use them.
  • Explain the Joule-Thomson effect, calculate the inversion temperature Ti = 2a/Rb and describe Linde's, Claude's and adiabatic demagnetisation methods.

LPG cylinders, liquid oxygen in hospitals and liquid rocket fuels all need gases turned into liquids. Some gases liquefy just by squeezing them; others must first be cooled a great deal. Thomas Andrews' experiments on carbon dioxide showed why.

Andrews' isotherms of carbon dioxide

Andrews measured the pressure and volume of a fixed mass of CO₂ at several fixed temperatures and plotted each set as an isotherm.

  • At a low temperature such as 13 °C, compressing the gas first reduces its volume as a gas (A to B). At B liquid starts to appear. Along the flat part B to C, gas and liquid coexist and the pressure stays constant while more gas condenses. At C everything is liquid, and beyond C the steep line shows that the liquid hardly compresses.
  • At higher temperatures (such as 21 °C) the flat part is shorter: liquid and gas coexist over a smaller range of volume.
  • At 31.1 °C the flat part shrinks to a single point, the critical point, at about 73 atm. Here liquid and gas become indistinguishable.
  • Above 31.1 °C (for example 48 °C) there is no flat part at all: CO₂ stays a gas at every pressure.

Critical constants

  • Critical temperature (Tc): the temperature above which a gas cannot be liquefied, however great the pressure.
  • Critical pressure (Pc): the minimum pressure needed to liquefy the gas at its critical temperature.
  • Critical volume (Vc): the volume occupied by one mole of the gas at Tc and Pc.
Critical constants of some gases (values from the Tamil Nadu textbook)
GasTc (K)Pc (atm)Vc (cm³ mol⁻¹)
Helium5.22.2657.8
Hydrogen33.212.8065
Nitrogen126.333.5490.1
Oxygen154.850.1478.0
Carbon dioxide304.272.994.0
Ammonia405.5111.372.5
Water647.4218.355.3

A higher Tc means stronger attractions and easier liquefaction. Water and ammonia, whose molecules attract strongly, have high critical temperatures; helium and hydrogen have extremely low ones. When a mixture of these gases is cooled from 700 K, water (Tc 647.4 K) can be liquefied first, then ammonia, then CO₂.

Critical constants from van der Waals constants

For one mole, (P + a/V²)(V − b) = RT. Multiply out: PV − Pb + a/V − ab/V² = RT. Multiply every term by V²/P and collect powers of V: V³ − (b + RT/P)V² + (a/P)V − ab/P = 0. This cubic has three roots for V. At the critical point all three become equal to Vc, so the cubic must be identical to (V − Vc)³ = V³ − 3VcV² + 3Vc²V − Vc³ = 0, with P = Pc and T = Tc. Comparing coefficients:

  1. Coefficient of V²: 3Vc = b + RTc/Pc
  2. Coefficient of V: 3Vc² = a/Pc
  3. Constant term: Vc³ = ab/Pc
  4. Divide (3) by (2): Vc³/3Vc² = (ab/Pc) ÷ (a/Pc), so Vc/3 = b and Vc = 3b.
  5. Put Vc = 3b in (2): Pc = a/3Vc² = a/(3 × 9b²), so Pc = a/27b².
  6. Put both in (1): 9b = b + RTc × 27b²/a, so 8b = 27Rb²Tc/a and Tc = 8a/27Rb.

Vc = 3b, Pc = a/27b², Tc = 8a/27Rb; conversely a = 3PcVc² and b = Vc/3.

Worked example 1: critical constants of CO₂

Use a = 3.59 dm⁶ atm mol⁻², b = 0.0427 dm³ mol⁻¹ and R = 0.0821 dm³ atm mol⁻¹ K⁻¹. Working: Tc = 8a/27Rb = (8 × 3.59) ÷ (27 × 0.0821 × 0.0427) = 28.72 ÷ 0.09465 = 303 K. Pc = a/27b² = 3.59 ÷ (27 × 0.0427²) = 3.59 ÷ (27 × 0.001823) = 3.59 ÷ 0.04923 = 72.9 atm. Vc = 3b = 3 × 0.0427 = 0.128 dm³ = 128 cm³ mol⁻¹. Tc and Pc agree well with the measured 304.2 K and 72.9 atm, but the measured Vc is 94 cm³ mol⁻¹, a reminder that the van der Waals equation is only approximate.

Joule-Thomson effect and inversion temperature

Joule and Thomson found that a compressed gas forced through a porous plug or narrow opening into a region of low pressure, without heat entering or leaving (adiabatically), becomes noticeably cooler. As the gas expands, its molecules move apart against their mutual attractions, and the energy for this comes from their kinetic energy. This is the Joule-Thomson effect.

A gas cools on such expansion only below a temperature characteristic of that gas, its inversion temperature, Ti = 2a/Rb. At Ti there is no change in temperature; above Ti the gas actually warms on expanding. An ideal gas (a = 0) shows no Joule-Thomson effect at all, because its molecules do not attract one another. Most gases, such as N₂ and O₂, have inversion temperatures well above room temperature and cool on expansion directly. Hydrogen and helium have very low inversion temperatures, so they must first be pre-cooled below them before the Joule-Thomson effect can cool them further.

Worked example 2: inversion temperatures

(a) For CO₂ with a = 3.59 and b = 0.0427: Ti = 2a/Rb = (2 × 3.59) ÷ (0.0821 × 0.0427) = 7.18 ÷ 0.003506 = 2048 K, far above room temperature, so CO₂ cools on expansion. (b) For hydrogen, take a = 0.244 dm⁶ atm mol⁻² and b = 0.0266 dm³ mol⁻¹: Ti = (2 × 0.244) ÷ (0.0821 × 0.0266) = 0.488 ÷ 0.002184 = 223 K (about −50 °C), so at room temperature hydrogen warms on expansion and must be pre-cooled. Note that Ti = (27/4)Tc for a van der Waals gas: 303 × 6.75 = 2045 K, agreeing with (a).

Methods of liquefying gases

Ways to liquefy gases

  • Linde's method
    • Uses the Joule-Thomson effect repeatedly
    • Compressed gas expands through a valve and cools
    • The cooled gas pre-cools incoming gas until it liquefies
  • Claude's process
    • Gas also does mechanical work (drives a piston) as it expands
    • Doing work removes extra energy, so cooling is greater
  • Adiabatic demagnetisation
    • A magnetic salt such as gadolinium sulphate is magnetised, then the field is removed
    • Gives temperatures around 10⁻⁴ K, very close to absolute zero

Key takeaways: above Tc no pressure liquefies a gas; at the critical point liquid and gas become one. Vc = 3b, Pc = a/27b², Tc = 8a/27Rb. Gases cool on Joule-Thomson expansion only below Ti = 2a/Rb; H₂ and He must be pre-cooled. Linde uses the Joule-Thomson effect, Claude adds work, and adiabatic demagnetisation reaches near 0 K.

Check your understanding

  1. 1. The critical temperature of CO₂ is 304.2 K. Which statement is correct?

    1. CO₂ can be liquefied at 320 K if enough pressure is applied.
    2. CO₂ cannot be liquefied at any temperature above 304.2 K, however high the pressure.
    3. CO₂ liquefies on its own when cooled to 304.2 K at 1 atm.
    4. CO₂ is a liquid at all temperatures below 304.2 K.
    Show answer

    Answer: B. Critical temperature is the temperature above which a gas cannot be liquefied by pressure alone. Below Tc it can be liquefied, but only if the pressure is high enough; at 1 atm CO₂ does not form a liquid.

  2. 2. Four gases have nearly the same b, and their a values are in the order Q < R < S < P. Which is the most easily liquefied?

    1. Q
    2. R
    3. S
    4. P
    Show answer

    Answer: D. With b fixed, Tc = 8a/27Rb rises with a. P has the largest a, so the strongest attractions and the highest critical temperature, and it liquefies most easily.

  3. 3. Using the van der Waals equation, what is the critical volume of a gas with b = 0.0391 dm³ mol⁻¹?

    1. 0.0130 dm³ mol⁻¹
    2. 0.1173 dm³ mol⁻¹
    3. 0.0782 dm³ mol⁻¹
    4. 0.3519 dm³ mol⁻¹
    Show answer

    Answer: B. Vc = 3b = 3 × 0.0391 = 0.1173 dm³ mol⁻¹ (117.3 cm³ mol⁻¹). 0.0130 is b/3, a common slip.

  4. 4. A gas has a = 1.39 dm⁶ atm mol⁻² and b = 0.0391 dm³ mol⁻¹. What is its inversion temperature? (R = 0.0821 dm³ atm mol⁻¹ K⁻¹)

    1. 433 K
    2. 128 K
    3. 866 K
    4. 1732 K
    Show answer

    Answer: C. Ti = 2a/Rb = (2 × 1.39) ÷ (0.0821 × 0.0391) = 2.78 ÷ 0.003210 = 866 K. 433 K forgets the factor 2. For comparison, Tc = 8a/27Rb = 11.12 ÷ 0.08667 = 128 K, and 866 ÷ 128 ≈ 6.75 = 27/4.

  5. 5. Why does an ideal gas show no cooling when it expands through a valve into a low-pressure region?

    1. It is always above its inversion temperature.
    2. Its molecules do work equal to the kinetic energy lost.
    3. Its molecules exert no attractive forces on one another.
    4. Its molecules collide without losing energy.
    Show answer

    Answer: C. Joule-Thomson cooling happens because molecules use kinetic energy to move apart against their attractions. An ideal gas has no attractions (a = 0, so Ti = 2a/Rb = 0), so no energy is used and the temperature does not change.

Sign in to keep track of the lessons you finish.

Next lesson → Final self-assessment: Gaseous State

Privacy · Terms · Refunds · Delivery