- Practice
- About 26 min
- 5 practice questions
Force on conductors, torque on a current loop and the moving coil galvanometer
Find the force on a current-carrying conductor with Fleming's left hand rule, the force between parallel currents and the definition of the ampere, the torque on a current loop, and the working, sensitivity and conversion of a moving coil galvanometer into an ammeter and a voltmeter.
If something looks wrong, please tell us.
By the end of this lesson you can
- Derive F⃗ = I(l⃗ × B⃗) from the Lorentz force on the drifting electrons.
- Use Fleming's left hand rule.
- Derive the force per unit length μ₀I₁I₂/(2πr) between parallel wires and state the definition of the ampere.
- Derive the torque τ = NIAB sin θ on a rectangular coil, τ⃗ = p⃗_m × B⃗.
- Explain the moving coil galvanometer, current and voltage sensitivity and figure of merit.
- Convert a galvanometer into an ammeter (shunt) and a voltmeter (series resistance).
A magnetic field pushes on moving charges, so it pushes on a wire full of drifting electrons. This sideways push on a current-carrying conductor is what turns every electric motor and moves the pointer of every analogue meter.
Force on a current-carrying conductor
Take a small length dl of a conductor of cross-section A with n free electrons per unit volume drifting at v⃗_d (so I = neAv_d). Each electron feels −e(v⃗_d × B⃗). The element holds nA dl electrons, so dF⃗ = −enA dl (v⃗_d × B⃗). Since the current element is I dl⃗ = −enA dl v⃗_d, dF⃗ = I(dl⃗ × B⃗). For a straight conductor of length l in a uniform field: F⃗ = I(l⃗ × B⃗), magnitude F = BIl sin θ. The force is zero when the conductor lies along the field (θ = 0°) and greatest, BIl, when it is perpendicular to the field.
Fleming's left hand rule: stretch the forefinger, middle finger and thumb of the left hand mutually perpendicular. If the forefinger points along the magnetic field and the middle finger along the current, the thumb points along the force on the conductor.
Worked example 1: force on a wire, and a floating rod
(a) A wire 0.40 m long carrying 5.0 A lies in a 0.30 T field. Perpendicular to the field: F = BIl = 0.30 × 5.0 × 0.40 = 0.60 N. At 30° to the field: F = 0.60 × sin 30° = 0.30 N. (b) A horizontal metal rod with mass per unit length 0.050 kg m⁻¹ lies at right angles to a horizontal field of 0.49 T. What current makes the magnetic force support its weight? For a length l, BIl = (0.050 l)g, so I = 0.050 × 9.8/0.49 = 1.0 A, in the direction (by Fleming's rule) that makes the force upward.
Force between two long parallel conductors
Two long straight parallel wires A and B, a distance r apart in air, carry currents I₁ and I₂ in the same direction. The current I₁ produces a field B₁ = μ₀I₁/(2πr) at wire B, perpendicular to B. The force on a length dl of B is I₂ dl B₁, so the force per unit length is F/l = μ₀I₁I₂/(2πr), and by the rules of direction it points towards A. In the same way wire A is pulled towards B. So parallel currents in the same direction attract, and currents in opposite directions repel.
Definition of the ampere (as given in the textbook): one ampere is the constant current which, flowing in each of two infinitely long, straight, parallel conductors placed 1 m apart in vacuum, makes each conductor experience a force of 2 × 10⁻⁷ newton per metre of length. Check: μ₀ × 1 × 1/(2π × 1) = 2 × 10⁻⁷ N m⁻¹. The textbook also notes that since 20 May 2019 the ampere has been defined from the elementary charge: one ampere is the current corresponding to 1/(1.602 176 634 × 10⁻¹⁹) elementary charges passing per second.
Worked example 2: two parallel wires
Two long parallel wires 5.0 cm apart each carry 10 A in the same direction. F/l = μ₀I₁I₂/(2πr) = (2 × 10⁻⁷ × 10 × 10)/0.050 = (2 × 10⁻⁵)/0.050 = 4.0 × 10⁻⁴ N m⁻¹, attractive. If one current is reversed, the force has the same size but is repulsive.
Torque on a current loop
A rectangular loop PQRS (length a, breadth b) carries current I in a uniform field B⃗, its normal n̂ making angle θ with B⃗. The forces on the two sides of length b (QR and SP) are equal, opposite and along the same line, so they cancel. The forces on the two sides of length a (PQ and RS) are each IaB, equal and opposite, but along different lines: they form a couple. Seen from the side, each acts at a lever arm (b/2) sin θ about the central axis, so the total torque is τ = 2 × (b/2) sin θ × IaB = I(ab)B sin θ = IAB sin θ. For N turns, τ = NIAB sin θ; in vector form τ⃗ = p⃗_m × B⃗ with p⃗_m = NIA n̂. The torque turns the loop so that its normal lines up with the field. It is greatest (NIAB) when the plane of the loop is parallel to the field (θ = 90°), and zero when the plane is perpendicular to the field (θ = 0° or 180°). This torque drives electric motors.
Worked example 3: torque on a coil
A coil of 100 turns, each 5.0 cm × 8.0 cm, carries 0.50 A in a 0.20 T field. Step 1: A = 0.050 × 0.080 = 4.0 × 10⁻³ m². Step 2: maximum torque (plane parallel to B) = NIAB = 100 × 0.50 × 4.0 × 10⁻³ × 0.20 = 0.040 N m. Step 3: with the normal at 30° to the field, τ = 0.040 × sin 30° = 0.020 N m.
The moving coil galvanometer
Principle: a current-carrying coil in a magnetic field experiences a torque. Construction: a rectangular coil of many turns of insulated thin copper wire is wound on a light metal frame, with a cylindrical soft-iron core placed symmetrically inside it. The coil hangs between the concave (hemispherical) pole pieces of a horseshoe magnet, from a fine phosphor-bronze strip that carries a small mirror and is fixed to a torsion head; its lower end is attached to a phosphor-bronze hair spring. The deflection is read with a lamp and scale using the mirror. The strip and spring also carry the current to the coil.
Working: the curved pole pieces and the iron core make the field radial, so whatever the coil's position its plane is always along the field. The sides of length b are parallel to the field and feel no force; the sides of length l are always perpendicular to it and feel equal, opposite forces, giving a deflecting torque τ = NIAB (always the maximum value). The suspension twists and produces a restoring torque Kθ, where K is the restoring couple per unit twist. At equilibrium NIAB = Kθ, so I = (K/NAB)θ = Gθ. G = K/(NAB) is the galvanometer constant (current reduction factor). Because the field is radial, θ is proportional to I and the scale is uniform.
- Figure of merit: the current needed to produce a deflection of one scale division.
- Current sensitivity I_S = θ/I = NAB/K = 1/G: deflection per unit current. It increases with more turns N, a stronger field B, a larger area A and a smaller couple per unit twist K. Phosphor bronze is used because its couple per unit twist is very small.
- Voltage sensitivity V_S = θ/V = NAB/(KR_g) = I_S/R_g: deflection per unit voltage, where R_g is the galvanometer's resistance. Increasing the number of turns increases R_g too, so it does not necessarily raise the voltage sensitivity.
Worked example 4: sensitivity of a galvanometer
A galvanometer coil has 60 turns, each of area 1.5 × 10⁻³ m², in a radial field of 0.10 T; the restoring couple is 3.0 × 10⁻⁸ N m per division, and the coil's resistance is 50 Ω. Step 1: I_S = NAB/K = (60 × 1.5 × 10⁻³ × 0.10)/(3.0 × 10⁻⁸) = (9.0 × 10⁻³)/(3.0 × 10⁻⁸) = 3.0 × 10⁵ div A⁻¹, i.e. 0.30 division per μA. Step 2: V_S = I_S/R_g = 3.0 × 10⁵/50 = 6.0 × 10³ div V⁻¹ = 6.0 divisions per mV. Step 3: figure of merit = 1/I_S ≈ 3.3 × 10⁻⁶ A per division.
Converting a galvanometer into an ammeter and a voltmeter
Ammeter. An ammeter is connected in series and must have a very low resistance so that it does not change the current it measures. A low resistance S, the shunt, is connected in parallel with the galvanometer. If I_g gives full-scale deflection and the circuit current is I, the shunt carries I − I_g, and the voltages are equal: I_gR_g = (I − I_g)S, so S = I_gR_g/(I − I_g), and I_g = [S/(S + R_g)]I ∝ I. The ammeter's resistance R_a = R_gS/(R_g + S) is small. To increase the range n times (I = nI_g), S = R_g/(n − 1). An ideal ammeter has zero resistance; a real one reads slightly less than the true current, with percentage error (I_ideal − I_actual)/I_ideal × 100%.
Voltmeter. A voltmeter is connected in parallel and must have a very high resistance so that it draws almost no current. A high resistance R_h is connected in series with the galvanometer. For full-scale deflection at voltage V: I_g = V/(R_g + R_h), so R_h = V/I_g − R_g, and the voltmeter's resistance is R_v = R_g + R_h. Since I_g ∝ V, the deflection measures the voltage. To increase the range n times, R_h = (n − 1)R_g. An ideal voltmeter has infinite resistance.
Galvanometer conversions
-
Ammeter
- Low shunt S in parallel
- S = I_gR_g/(I − I_g)
- Connected in series
- Ideal resistance: zero
-
Voltmeter
- High resistance R_h in series
- R_h = V/I_g − R_g
- Connected in parallel
- Ideal resistance: infinite
Worked example 5: shunt and series resistance
A galvanometer of resistance 50 Ω gives full-scale deflection for 5.0 mA. (a) Ammeter of range 0-1.0 A: S = I_gR_g/(I − I_g) = (0.0050 × 50)/(1.0 − 0.0050) = 0.25/0.995 ≈ 0.25 Ω, in parallel. (b) Voltmeter of range 0-10 V: R_h = V/I_g − R_g = 10/0.0050 − 50 = 2000 − 50 = 1950 Ω, in series. The voltmeter's total resistance is 2000 Ω.
F = BIl sin θ (Fleming's left hand rule). Parallel wires: F/l = μ₀I₁I₂/(2πr). Coil: τ = NIAB sin θ. Galvanometer: I = (K/NAB)θ; I_S = NAB/K; V_S = I_S/R_g. Shunt S = I_gR_g/(I − I_g); series R_h = V/I_g − R_g.
Key takeaways
- A conductor in a field feels F = BIl sin θ, given in direction by Fleming's left hand rule.
- Like parallel currents attract, unlike repel; 2 × 10⁻⁷ N m⁻¹ for 1 A in wires 1 m apart.
- A coil feels τ = NIAB sin θ, largest when its plane is along the field.
- In a moving coil galvanometer the radial field makes the deflection proportional to the current.
- Ammeter: galvanometer + low shunt in parallel. Voltmeter: galvanometer + high resistance in series.
Check your understanding
-
1. Two long parallel wires carry currents in opposite directions. They:
- attract each other
- repel each other
- exert no force on each other
- twist about their axes
Show answer
Answer: B. Parallel currents in the same direction attract; currents in opposite directions repel. The force per unit length is μ₀I₁I₂/(2πr) in either case.
-
2. Two long straight wires 1 m apart in vacuum each carry 1 A. The force per metre on each wire is:
- 1 N
- 4π × 10⁻⁷ N
- 2 × 10⁻⁷ N
- 10⁻⁷ N
Show answer
Answer: C. F/l = μ₀I₁I₂/(2πr) = (4π × 10⁻⁷ × 1 × 1)/(2π × 1) = 2 × 10⁻⁷ N per metre. This is the textbook's definition of the ampere.
-
3. A current-carrying rectangular coil is in a uniform magnetic field. The torque on it is greatest when:
- the plane of the coil is perpendicular to the field
- the normal to the coil is along the field
- the coil carries no current
- the plane of the coil is parallel to the field
Show answer
Answer: D. τ = NIAB sin θ, where θ is the angle between the normal and B. It is greatest when θ = 90°, i.e. when the plane of the coil is parallel to the field; it is zero when the plane is perpendicular to the field.
-
4. The pole pieces of a moving coil galvanometer are made concave and a soft-iron core is placed inside the coil so that:
- the field is radial, making the deflection proportional to the current
- the coil becomes heavier and steadier
- no current flows through the spring
- the field becomes zero
Show answer
Answer: A. A radial field keeps the plane of the coil along the field in every position, so the deflecting torque is always NIAB. Balancing it with Kθ gives θ ∝ I and a uniform scale.
-
5. A galvanometer of resistance 100 Ω gives full-scale deflection for 1 mA. To convert it into an ammeter reading up to 101 mA, the shunt needed is:
- 100 Ω in series
- 0.1 Ω in parallel
- 1 Ω in parallel
- 9900 Ω in series
Show answer
Answer: C. The range is increased n = 101/1 = 101 times, so S = R_g/(n − 1) = 100/100 = 1 Ω, connected in parallel. (Check: S = I_gR_g/(I − I_g) = 0.001 × 100/0.100 = 1 Ω.)
Sign in to keep track of the lessons you finish.