- Practice
- About 30 min
- 5 practice questions
Alternating current: mean and RMS values, phasors and AC circuits
Find the mean and RMS values of AC, use phasors, analyse pure R, L and C circuits and the series RLC circuit (impedance, phase angle), and work out resonance and the Q-factor.
If something looks wrong, please tell us.
By the end of this lesson you can
- Write v = V_m sin ωt and read peak value, frequency and period from it.
- Derive I_av = 2I_m/π = 0.637 I_m (half cycle) and I_RMS = I_m/√2 = 0.707 I_m.
- Represent AC by phasors and state the phase relation in pure R, L and C circuits.
- Calculate X_L = ωL, X_C = 1/ωC, the impedance Z and phase angle φ of a series RLC circuit.
- Find the resonant frequency f_r = 1/(2π√LC) and the Q-factor (1/R)√(L/C).
An alternating voltage changes polarity at regular intervals, so the current it drives keeps reversing. If the waveform is a sine wave, v = V_m sin ωt, where V_m is the peak value (amplitude) and ω = 2πf is the angular frequency. The resulting current is also sinusoidal, i = I_m sin ωt. Sine waves are common in nature, in water waves and pendulums as well as in AC.
Mean (average) value
Over a full cycle, the positive and negative halves of a symmetrical AC cancel, so the average is zero. The average value is therefore taken over a half cycle: it is the area under one half-cycle divided by its base length π. With θ = ωt, area = ∫₀^π I_m sin θ dθ = I_m[−cos θ]₀^π = I_m[1 + 1] = 2I_m. So I_av = 2I_m/π = 0.637 I_m (and −0.637 I_m for the negative half). For n sampled currents in a half cycle, I_av = (i₁ + i₂ + … + i_n)/n.
RMS (effective) value
The root mean square value is the square root of the mean of the squares of the current over one cycle. Area under one cycle of i² = ∫₀^{2π} I_m² sin²θ dθ. Using sin²θ = (1 − cos 2θ)/2, this is (I_m²/2)[θ − (sin 2θ)/2]₀^{2π} = (I_m²/2)(2π) = πI_m². Dividing by the base 2π gives I_m²/2, so I_RMS = I_m/√2 = 0.707 I_m; likewise V_RMS = 0.707 V_m. The RMS value is also called the effective value: it is the steady current that would produce the same heat in the same resistor in the same time. Appliance ratings and the domestic supply (230 V, 50 Hz) are RMS values; the peak of the supply is √2 × 230 ≈ 325 V.
I_av = 2I_m/π = 0.637 I_m (half cycle); I_RMS = I_m/√2 = 0.707 I_m; X_L = ωL; X_C = 1/ωC; Z = √(R² + (X_L − X_C)²); tan φ = (X_L − X_C)/R.
Worked example 1: reading an AC equation
i = 10 sin(100πt) A. Peak I_m = 10 A. Frequency f = ω/2π = 100π/2π = 50 Hz; period T = 1/f = 0.02 s. RMS = 0.707 × 10 = 7.07 A. Half-cycle average = 0.637 × 10 = 6.37 A. At t = 1/600 s: 100π × 1/600 = π/6 rad = 30°, so i = 10 × 0.5 = 5.0 A.
Phasors
A phasor is a vector that rotates anticlockwise about the origin with angular velocity ω. Its length is the peak value, its angle with the positive x-axis is the phase ωt, and its projection on the vertical axis is the instantaneous value V_m sin ωt. One full turn traces one cycle. If the current is i = I_m sin(ωt + φ), its phasor is ahead of the voltage phasor by φ: the current leads by φ. For i = I_m sin(ωt − φ) it lags. A diagram of several phasors with their phase relations is a phasor diagram.
Pure R, pure L and pure C circuits
Resistor: by Kirchhoff's loop rule v = iR, so i = (V_m/R) sin ωt. Current and voltage are in phase: they reach maxima and minima together. Inductor: the back emf is −L di/dt, so V_m sin ωt = L di/dt. Integrating, i = −(V_m/ωL) cos ωt = (V_m/ωL) sin(ωt − π/2). The current lags the voltage by π/2, and I_m = V_m/ωL. The quantity X_L = ωL = 2πfL is the inductive reactance (ohm). Capacitor: q = CV_m sin ωt, so i = dq/dt = CV_mω cos ωt = (V_m/(1/ωC)) sin(ωt + π/2). The current leads by π/2, and X_C = 1/ωC = 1/(2πfC) is the capacitive reactance.
For steady DC, f = 0: X_L = 0, so an ideal inductor lets DC through freely, but X_C is infinite, so a capacitor blocks DC. An inductor opposes AC because the changing current produces a back emf. A memory aid used in the textbook: ELI (emf leads current in an inductor) and ICE (current leads emf in a capacitor).
Three pure AC circuits
-
Pure R
- Opposition: R
- i in phase with v
- Power factor 1
-
Pure L
- Opposition: X_L = ωL, grows with f
- i lags v by 90°
- Power factor 0
-
Pure C
- Opposition: X_C = 1/ωC, falls with f
- i leads v by 90°
- Power factor 0
Worked example 2: reactances
(a) A 0.20 H inductor of negligible resistance is on 230 V, 50 Hz. X_L = 2πfL = 2 × 3.1416 × 50 × 0.20 = 62.8 Ω; I_RMS = 230/62.8 = 3.66 A. (b) A 50 μF capacitor on the same supply: X_C = 1/(2πfC) = 1/(2 × 3.1416 × 50 × 50 × 10⁻⁶) = 1/0.015708 = 63.7 Ω; I_RMS = 230/63.7 = 3.61 A.
Series RLC circuit
R, L and C in series carry the same current i, so the current phasor is drawn as the reference. V_R = I_mR is in phase with it, V_L = I_mX_L leads it by 90°, and V_C = I_mX_C lags it by 90°. V_L and V_C point in opposite directions, so (taking V_L > V_C) they combine to V_L − V_C. Adding this at right angles to V_R: V_m² = V_R² + (V_L − V_C)² = I_m²[R² + (X_L − X_C)²]. So I_m = V_m/Z with impedance Z = √(R² + (X_L − X_C)²), the effective opposition of the circuit. The phase angle between v and i is given by tan φ = (V_L − V_C)/V_R = (X_L − X_C)/R.
- X_L > X_C: φ positive, voltage leads current; the circuit is inductive.
- X_L < X_C: φ negative, current leads voltage; the circuit is capacitive.
- X_L = X_C: φ = 0, in phase; the circuit is resistive.
Worked example 3: impedance and phase
R = 40 Ω, X_L = 80 Ω, X_C = 50 Ω, on 100 V RMS. Z = √(40² + (80 − 50)²) = √(1600 + 900) = √2500 = 50 Ω. I_RMS = 100/50 = 2.0 A. tan φ = 30/40 = 0.75, so φ = 36.9°. Since X_L > X_C, the voltage leads the current by 36.9° (inductive circuit).
Resonance and the Q-factor
When the source frequency equals the natural frequency 1/√(LC) of the circuit, the current is a maximum: electrical resonance. The condition is X_L = X_C, i.e. ω_rL = 1/(ω_rC), giving ω_r = 1/√(LC) and f_r = 1/(2π√(LC)). At resonance Z = R (its minimum), so I_m = V_m/R. A small R gives a large current and a sharp resonance curve; a large R gives a flat one. Resonance needs both L and C, since only then can V_L and V_C (180° apart) cancel; it does not occur in RL or RC circuits. Use: tuning a radio or TV: a variable capacitor changes f_r until it matches the wanted station, whose signal then gives the largest current.
At resonance, the voltages across L and C can be much larger than the applied voltage. The Q-factor is the ratio of the voltage across L (or C) at resonance to the applied voltage. Since the applied voltage then equals I_mR, Q = I_mX_L/(I_mR) = ω_rL/R = (1/R)√(L/C). It tells how many times the voltage across L or C exceeds the applied voltage.
Worked example 4: resonance
L = 0.10 H, C = 10 μF, R = 10 Ω. Step 1: LC = 0.10 × 10 × 10⁻⁶ = 1.0 × 10⁻⁶ s², √(LC) = 1.0 × 10⁻³ s. Step 2: ω_r = 1/(1.0 × 10⁻³) = 1000 rad s⁻¹ and f_r = 1000/(2π) = 159 Hz. Step 3: Q = ω_rL/R = 1000 × 0.10/10 = 10. Check: (1/R)√(L/C) = 0.1 × √(0.10/10⁻⁵) = 0.1 × √10 000 = 0.1 × 100 = 10. With 2.0 V applied at resonance, the voltage across L (and across C) is 10 × 2.0 = 20 V.
Key takeaways
- Mean value over a half cycle 0.637 I_m; RMS value 0.707 I_m; ratings like 230 V are RMS.
- A phasor's length is the peak value and its vertical projection the instantaneous value.
- R: in phase. L: current lags by 90°, X_L = ωL. C: current leads by 90°, X_C = 1/ωC.
- Series RLC: Z = √(R² + (X_L − X_C)²), tan φ = (X_L − X_C)/R.
- Resonance at f_r = 1/(2π√LC) where Z = R; Q = (1/R)√(L/C) is the voltage magnification.
Check your understanding
-
1. The domestic supply is 230 V RMS. Its peak value is about:
- 325 V
- 163 V
- 230 V
- 460 V
Show answer
Answer: A. V_m = √2 × V_RMS = 1.414 × 230 ≈ 325 V.
-
2. In a purely inductive AC circuit, the current:
- is in phase with the voltage
- leads the voltage by π/2
- lags behind the voltage by π/2
- leads the voltage by π
Show answer
Answer: C. From V_m sin ωt = L di/dt, i = (V_m/ωL) sin(ωt − π/2): the current lags by π/2 (ELI).
-
3. A capacitor of capacitance (100/π) μF is connected to a 50 Hz supply. Its capacitive reactance is:
- 10 Ω
- 100 Ω
- 1000 Ω
- π Ω
Show answer
Answer: B. X_C = 1/(2πfC) = 1/(2π × 50 × (100/π) × 10⁻⁶) = 1/(100 × 100 × 10⁻⁶) = 1/0.01 = 100 Ω.
-
4. A series RLC circuit has R = 30 Ω, X_L = 90 Ω and X_C = 50 Ω. Its impedance is:
- 170 Ω
- 70 Ω
- 40 Ω
- 50 Ω
Show answer
Answer: D. Z = √(R² + (X_L − X_C)²) = √(30² + 40²) = √(900 + 1600) = √2500 = 50 Ω. Simply adding the values (170 Ω) ignores the phase differences.
-
5. A series LCR circuit has L = 4 H and C = 25 μF. Its resonant angular frequency is:
- 100 rad s⁻¹
- 10 rad s⁻¹
- 1000 rad s⁻¹
- 15.9 rad s⁻¹
Show answer
Answer: A. LC = 4 × 25 × 10⁻⁶ = 10⁻⁴ s², √(LC) = 0.01 s, ω_r = 1/0.01 = 100 rad s⁻¹. (15.9 is f_r in hertz, not ω_r.)
Sign in to keep track of the lessons you finish.