• Practice
  • About 25 min
  • 5 practice questions

Eddy currents, self-induction and mutual induction

Explain eddy currents, how they are reduced and used; define self and mutual inductance; derive L for a long solenoid, M for two coaxial solenoids and the energy ½Li² stored in an inductor.

If something looks wrong, please tell us.

By the end of this lesson you can

  • Explain what eddy currents are, why they waste energy, and how laminations reduce them.
  • Describe four uses of eddy currents.
  • Define self-inductance L and the henry, and explain why inductance is 'electrical inertia'.
  • Derive L = μ₀n²Al for a long solenoid and the energy U = ½Li² stored in it.
  • Define mutual inductance M and derive M = μ₀n₁n₂A₂l for two coaxial solenoids.

Faraday's law does not need a wire loop. Whenever flux through any piece of metal changes, emfs are induced in it. This lesson looks first at currents induced in solid metal, and then at induction produced by a coil's own changing current and by a neighbouring coil's current.

Eddy currents

In a sheet or block of metal there is no single loop for the induced current, so it circulates in closed whirls inside the metal, like eddies in water. These are eddy currents (also called Foucault currents). A simple demonstration: a metal-disc pendulum swinging between the poles of a strong electromagnet. With the magnet off it swings many times, damped only by air. With the magnet on, eddy currents in the disc oppose its motion (Lenz's law) and it stops within a few swings. If slots are cut in the disc, the eddies cannot circulate freely, the damping falls, and it swings much longer.

Drawback: eddy currents turn energy into heat. In transformer cores and motor armatures this is a loss. It is reduced by making the core from thin laminations insulated from each other (and motor windings from groups of insulated wires), so the eddy paths are broken into tiny, high-resistance loops.

Uses of eddy currents

  • Induction stove A coil under the cooking zone carries high-frequency AC; eddy currents in a suitable metal pan heat it by Joule heating.
  • Eddy current brake Electromagnets near the rails (linear brake) or a disc on the wheel shaft spinning between magnet poles (circular brake); the eddy currents oppose the motion. Used in high-speed trains and roller coasters.
  • Eddy current testing A coil carrying AC induces eddy currents in a test surface; a crack or air bubble changes their phase and amplitude, revealing the defect without damaging the object.
  • Electromagnetic damping The galvanometer coil is wound on a soft iron cylinder; eddy currents in it stop the coil swinging so it settles quickly to a steady reading.

According to the textbook, the 50 Hz domestic supply is raised to roughly 20-40 kHz before it feeds an induction-stove coil, because a faster-changing field induces stronger eddy currents.

Self-induction

An inductor (coil, solenoid or toroid) stores energy in a magnetic field when a current flows in it. The current in a coil sets up flux through the coil itself. If the current changes, this flux changes and an emf is induced in the same coil: self-induction. The flux linkage is proportional to the current: NΦ_B = Li, where L is the self-inductance. From Faraday's law, ε = −d(NΦ_B)/dt = −L di/dt.

  • Definition 1: L is the flux linkage per unit current, L = NΦ_B / i.
  • Definition 2: L is the opposing emf when the current changes at 1 A s⁻¹, L = −ε/(di/dt).
  • Unit: henry; 1 H = 1 Wb A⁻¹ = 1 V s A⁻¹. Dimensions [M L² T⁻² A⁻²]. L is a scalar.
  • A coil has 1 H if a current changing at 1 A s⁻¹ induces an opposing emf of 1 V.

Physical meaning. Mass resists change of linear motion and moment of inertia resists change of rotation. Inductance plays the same role for current: when a circuit is switched on, the self-induced emf opposes the growth of current; when it is switched off, the emf reverses and opposes the decay. Inductance tries to keep the current as it was.

Self-inductance of a long solenoid

Take a long solenoid of length l, cross-section A and n turns per metre (total N = nl). The field inside is uniform, B = μ₀ni, so the flux through each turn is Φ_B = μ₀niA. The flux linkage is NΦ_B = (nl)(μ₀niA) = μ₀n²Al i. Comparing with NΦ_B = Li gives L = μ₀n²Al. L depends only on the geometry and on the medium inside: with a core of relative permeability μ_r, L = μ₀μ_r n²Al.

Energy stored in an inductor

While the current is being built up, work must be done against the back emf. Moving a charge dq = i dt against ε = −L di/dt needs dW = −ε dq = L i di. Total work to reach current i: W = ∫₀ⁱ L i di = ½Li². This is stored as magnetic potential energy, U_B = ½Li². For a solenoid, dividing by the volume Al and using L = μ₀n²Al and B = μ₀ni gives the energy density u_B = B²/(2μ₀).

ε = −L di/dt; L = μ₀μ_r n²Al; U_B = ½Li²; u_B = B²/2μ₀; M = μ₀μ_r n₁n₂A₂l.

Worked example 1: inductance and induced emf of a solenoid

An air-core solenoid has 1000 turns, length 0.50 m and radius 2.0 cm. (a) Find L. (b) Find the average self-induced emf if the current rises from 0 to 2.0 A in 0.10 s. (c) Find L if a core of μ_r = 500 is inserted. (a) A = πr² = 3.1416 × (0.020)² = 1.257 × 10⁻³ m². Writing n = N/l, L = μ₀N²A/l = (4π × 10⁻⁷ × 1000² × 1.257 × 10⁻³)/0.50 = (1.2566 × 1.257 × 10⁻³)/0.50 = 3.16 × 10⁻³ H. (b) di/dt = 2.0/0.10 = 20 A s⁻¹, so |ε| = 3.16 × 10⁻³ × 20 = 6.3 × 10⁻² V = 63 mV. (c) L = 500 × 3.16 × 10⁻³ = 1.58 H.

Worked example 2: energy in an inductor

A 0.25 H inductor carries 4.0 A. Energy stored U = ½Li² = 0.5 × 0.25 × (4.0)² = 0.5 × 0.25 × 16 = 2.0 J.

Mutual induction

When the current in one coil changes, an emf is induced in a neighbouring coil: mutual induction. If current i₁ in coil 1 links flux Φ₂₁ with each of the N₂ turns of coil 2, then N₂Φ₂₁ = M₂₁ i₁, and the emf in coil 2 is ε₂ = −M₂₁ di₁/dt. M₂₁ is the mutual inductance of coil 2 with respect to coil 1. Similarly N₁Φ₁₂ = M₁₂ i₂. For any pair of coils M₁₂ = M₂₁ = M. Its unit is also the henry: two coils have M = 1 H if a current changing at 1 A s⁻¹ in one induces an opposing emf of 1 V in the other. M depends on the sizes, shapes and turns of the coils, their relative orientation and the permeability of the medium.

Mutual inductance of two long coaxial solenoids

Two long solenoids of the same length l share an axis; solenoid 1 (area A₁, n₁ turns per metre) surrounds solenoid 2 (area A₂ < A₁, n₂ turns per metre). Current i₁ makes B₁ = μ₀n₁i₁ inside solenoid 1, so each turn of solenoid 2 links Φ₂₁ = μ₀n₁i₁A₂, and N₂Φ₂₁ = (n₂l)(μ₀n₁i₁A₂). So M₂₁ = μ₀n₁n₂A₂l. Now let i₂ flow in solenoid 2: its field B₂ = μ₀n₂i₂ exists only inside solenoid 2, so the effective area for solenoid 1 is again A₂, not A₁. That gives M₁₂ = μ₀n₁n₂A₂l, the same value. With a core: M = μ₀μ_r n₁n₂A₂l.

Worked example 3: finding M from an induced emf

The current in a coil rises from 1.0 A to 6.0 A in 0.020 s, and an emf of 0.50 V is induced in a nearby coil. Step 1: di₁/dt = 5.0/0.020 = 250 A s⁻¹. Step 2: M = ε₂/(di₁/dt) = 0.50/250 = 2.0 × 10⁻³ H = 2.0 mH. Step 3: when the first coil carries a steady 3.0 A, the flux linkage of the second coil is Mi₁ = 2.0 × 10⁻³ × 3.0 = 6.0 × 10⁻³ Wb (but no emf, since nothing is changing).

Worked example 4: coaxial solenoids

An outer solenoid has 1000 turns per metre and an inner one 3000 turns per metre; the inner one has cross-section 2.0 × 10⁻⁴ m², and both are 0.40 m long. M = μ₀n₁n₂A₂l = 4π × 10⁻⁷ × 1000 × 3000 × 2.0 × 10⁻⁴ × 0.40. Here 1000 × 3000 × 2.0 × 10⁻⁴ × 0.40 = 240, so M = 1.2566 × 10⁻⁶ × 240 = 3.0 × 10⁻⁴ H = 0.30 mH.

Key takeaways

  • Eddy currents whirl inside bulk metal when flux changes; they cause heating loss, cut by insulated laminations.
  • They are useful in induction stoves, eddy current brakes, non-destructive testing and galvanometer damping.
  • Self-induced emf ε = −L di/dt; L = μ₀μ_r n²Al for a long solenoid; inductance is electrical inertia.
  • An inductor stores U = ½Li²; the field's energy density is B²/2μ₀.
  • Mutual inductance M = μ₀μ_r n₁n₂A₂l uses the area of the smaller solenoid, and M₁₂ = M₂₁.

Check your understanding

  1. 1. The core of a transformer is made of thin sheets insulated from each other mainly to:

    1. increase the flux leakage
    2. make the core lighter
    3. reduce eddy current loss
    4. increase the copper loss
    Show answer

    Answer: C. Insulated laminations break the paths along which eddy currents would circulate, so much less energy is turned into heat in the core.

  2. 2. Which of these is NOT equal to one henry?

    1. 1 V A s⁻¹
    2. 1 Wb A⁻¹
    3. 1 V s A⁻¹
    4. 1 Ω s
    Show answer

    Answer: A. From L = NΦ/i, 1 H = 1 Wb A⁻¹. From L = ε/(di/dt), 1 H = 1 V/(A s⁻¹) = 1 V s A⁻¹. Since 1 Ω = 1 V A⁻¹, 1 Ω s is also 1 V s A⁻¹. Only 1 V A s⁻¹ has the wrong form.

  3. 3. When the current in a coil changes from +3 A to −3 A in 0.1 s, an average emf of 12 V is induced. The self-inductance is:

    1. 0.4 H
    2. 4 H
    3. 0.1 H
    4. 0.2 H
    Show answer

    Answer: D. The change is −3 − (+3) = −6 A, so di/dt = −6/0.1 = −60 A s⁻¹. L = |ε|/|di/dt| = 12/60 = 0.2 H. (Taking only 3 A as the change gives the wrong answer 0.4 H.)

  4. 4. The number of turns of a long solenoid is doubled, keeping its length and area the same. Its self-inductance becomes:

    1. twice as large
    2. four times as large
    3. half as large
    4. unchanged
    Show answer

    Answer: B. L = μ₀N²A/l, so L ∝ N². Doubling N multiplies L by 2² = 4.

  5. 5. An 80 mH inductor stores 0.36 J of energy. The current in it is:

    1. 3 A
    2. 9 A
    3. 4.5 A
    4. 1.5 A
    Show answer

    Answer: A. U = ½Li², so i² = 2U/L = 0.72/0.080 = 9 and i = 3 A.

Privacy · Terms · Refunds · Delivery