• Practice
  • About 30 min
  • 15 practice questions

Final self-assessment: Electromagnetic Induction and Alternating Current

Test yourself on the whole course: 15 questions with answers explained.

If something looks wrong, please tell us.

Attempt all 15 questions before reading any explanation. Work each numerical on paper with units, then check. These questions are harder than the lesson checks and often combine two ideas.

Final self-assessment

  1. 1. A coil of 100 turns and area 0.02 m² is in a uniform field of 0.5 T with its plane perpendicular to the field. It is turned in 0.1 s until its plane is parallel to the field. The average induced emf is:

    1. 1 V
    2. 10 V
    3. 0.1 V
    4. 100 V
    Show answer

    Answer: B. Initial flux per turn = BA cos 0° = 0.5 × 0.02 = 0.01 Wb; final = BA cos 90° = 0. ε = NΔΦ/Δt = 100 × 0.01/0.1 = 10 V.

  2. 2. The north pole of a bar magnet is pulled away from one end of a coil. Seen from the magnet, the induced current makes the near end of the coil:

    1. a south pole, attracting the magnet
    2. a north pole, repelling the magnet
    3. a north pole, attracting the magnet
    4. neither pole, since the magnet is moving away
    Show answer

    Answer: A. By Lenz's law the coil opposes the withdrawal, so it attracts the receding north pole: its near end becomes a south pole.

  3. 3. A metal rod 1.0 m long rotates at 10 rad s⁻¹ about one end in a plane perpendicular to a uniform field of 0.4 T. The emf between its ends is:

    1. 4 V
    2. 0.4 V
    3. 20 V
    4. 2 V
    Show answer

    Answer: D. ε = ½Bωl² = 0.5 × 0.4 × 10 × 1.0² = 2 V. Using Blv with the tip speed (10 m s⁻¹) would give 4 V, which is wrong because the speed varies along the rod; the average speed is half the tip speed.

  4. 4. A solid copper plate and an identical plate with slots cut in it swing as pendulums between the poles of a strong magnet. Compared with the solid plate, the slotted plate:

    1. stops sooner, since the slots increase the eddy currents
    2. stops at the same time
    3. keeps swinging longer, since the slots reduce the eddy currents
    4. stops at once, since slots make it non-magnetic
    Show answer

    Answer: C. The slots break up the circulating eddy current paths, so the eddy currents and their damping force are smaller. The slotted plate swings for longer.

  5. 5. An air-core solenoid has inductance 2.0 mH. With an iron core filling it, the inductance becomes 0.90 H. The relative permeability of the iron is:

    1. 45
    2. 4500
    3. 1.8
    4. 450
    Show answer

    Answer: D. L = μ₀μ_r n²Al, so μ_r = L_iron/L_air = 0.90/(2.0 × 10⁻³) = 450.

  6. 6. The magnetic energy density in a region where B = 0.5 T is about (μ₀ = 4π × 10⁻⁷ T m A⁻¹):

    1. 2.0 × 10⁵ J m⁻³
    2. 9.9 × 10⁴ J m⁻³
    3. 4.0 × 10⁵ J m⁻³
    4. 9.9 × 10⁻⁸ J m⁻³
    Show answer

    Answer: B. u = B²/2μ₀ = 0.25/(2 × 4π × 10⁻⁷) = 0.25/(2.513 × 10⁻⁶) = 9.9 × 10⁴ J m⁻³. Forgetting the 2 gives 2.0 × 10⁵.

  7. 7. A generator coil has 100 turns of area 0.1 m² and rotates at 50 rad s⁻¹ in a field of 0.2 T. The peak emf is:

    1. 100 V
    2. 10 V
    3. 50 V
    4. 1000 V
    Show answer

    Answer: A. ε_m = NBAω = 100 × 0.2 × 0.1 × 50 = 100 V.

  8. 8. A step-down transformer of efficiency 90% takes 2.0 kW from the mains and supplies its load at 50 V. The current in the load is:

    1. 40 A
    2. 4 A
    3. 36 A
    4. 3.6 A
    Show answer

    Answer: C. Output power = 0.90 × 2000 = 1800 W. I_s = P/V = 1800/50 = 36 A. Assuming 100% efficiency would give 40 A.

  9. 9. The same power is transmitted along the same line first at 11 kV and then at 110 kV. The ratio (loss at 11 kV)/(loss at 110 kV) is:

    1. 10
    2. 100
    3. 1/100
    4. 1
    Show answer

    Answer: B. I = P/V, so the current at 11 kV is 10 times the current at 110 kV. Loss = I²R, so the loss is 10² = 100 times greater at 11 kV.

  10. 10. A current i = 4√2 sin ωt A flows through a 10 Ω resistor. The heat produced in one minute is:

    1. 160 J
    2. 19 200 J
    3. 4800 J
    4. 9600 J
    Show answer

    Answer: D. I_RMS = I_m/√2 = 4 A. Heat = I_RMS² R t = 16 × 10 × 60 = 9600 J. Using the peak value (4√2) would double this to 19 200 J.

  11. 11. In a series RLC circuit R = 100 Ω, X_L = 50 Ω and X_C = 150 Ω. Which statement is correct?

    1. The voltage leads the current by 45°
    2. Current and voltage are in phase
    3. The current leads the voltage by 45°
    4. The current leads the voltage by 90°
    Show answer

    Answer: C. tan φ = (X_L − X_C)/R = (50 − 150)/100 = −1, so φ = −45°. A negative φ means a capacitive circuit: the current leads the voltage by 45°.

  12. 12. A series RLC circuit has R = 20 Ω, L = 0.2 H and C = 5 μF and is driven at its resonant frequency by a 5 V (RMS) source. The RMS voltage across the inductor is:

    1. 50 V
    2. 5 V
    3. 0.5 V
    4. 100 V
    Show answer

    Answer: A. Q = (1/R)√(L/C) = (1/20)√(0.2/5 × 10⁻⁶) = 0.05 × √40 000 = 0.05 × 200 = 10. At resonance V_L = Q × applied voltage = 10 × 5 = 50 V.

  13. 13. A series circuit of impedance 80 Ω and resistance 48 Ω is connected to 240 V RMS. The average power consumed is:

    1. 720 W
    2. 576 W
    3. 240 W
    4. 432 W
    Show answer

    Answer: D. I_RMS = 240/80 = 3 A; power factor = R/Z = 48/80 = 0.6; P = 240 × 3 × 0.6 = 432 W. Check: I²R = 9 × 48 = 432 W.

  14. 14. An RMS current of 10 A lags the voltage by 30°. The wattless component of the current is:

    1. 8.66 A
    2. 5 A
    3. 10 A
    4. 0 A
    Show answer

    Answer: B. Wattless current = I_RMS sin φ = 10 × sin 30° = 5 A. The wattful part is 10 cos 30° = 8.66 A.

  15. 15. In an ideal LC circuit the maximum charge on the capacitor is Q_m. At the instant the energy is shared equally between the capacitor and the inductor, the charge is:

    1. Q_m/2
    2. Q_m/4
    3. Q_m/√2
    4. zero
    Show answer

    Answer: C. Total energy = Q_m²/2C. Equal sharing means q²/2C = ½ × Q_m²/2C, so q² = Q_m²/2 and q = Q_m/√2.

Questions 1-3: lesson 1 (flux, Faraday, Lenz, motional emf). Questions 4-6: lesson 2 (eddy currents, self and mutual induction). Questions 7-9: lesson 3 (generators, transformers, transmission). Questions 10-12: lesson 4 (RMS value, RLC circuits, resonance). Questions 13-15: lesson 5 (power, wattless current, LC oscillations).

Sign in to keep track of the lessons you finish.

Privacy · Terms · Refunds · Delivery