Revision notes

Polymers: Practice

The key points, rules to remember, tables and diagrams from all 9 lessons, on one page for quick revision. To keep a copy, use your browser's Print and choose "Save as PDF".

Lesson 1

Classifying polymers: the four ways and the traps

Forces decide behaviour
ClassForces between chainsTypical behaviourExamples
ElastomersWeakest van der Waals forces, a few cross-linksStretch and return to shapeNatural rubber (vulcanised), Buna-S, Buna-N, neoprene
FibresStrong forces such as hydrogen bondsHigh tensile strength, thread-formingNylon 6,6, terylene
ThermoplasticsIntermediate forcesSoften on heating, harden on cooling, repeatedlyPolythene, polystyrene, PVC
Thermosetting polymersExtensive cross-linking formed on heatingSet permanently; cannot be remouldedBakelite, urea-formaldehyde resin

Four questions for every polymer: Where does it come from? What shape are its chains? Did it lose a small molecule as it formed? How strongly do its chains hold each other?

  • Semi-synthetic means a natural polymer chemically modified: rayon is the classic trap.
  • Branching lowers density and melting point; cross-linking makes a polymer hard and thermosetting.
  • Addition polymers keep the monomer's formula; condensation polymers lose a small molecule per link.
  • Elastomer < thermoplastic < fibre in strength of inter-chain forces; thermosets are fixed by cross-links.
Read the full lesson

Lesson 2

Addition polymers: monomers, conditions and quick calculations

Common addition polymers
PolymerMonomerNotes and uses
Low density polytheneEtheneHigh pressure, traces of oxygen or peroxide, free radical; branched; squeeze bottles, insulation
High density polytheneEtheneZiegler-Natta catalyst (triethylaluminium with titanium tetrachloride), low pressure; linear; buckets, pipes
PolypropenePropeneRopes, toys, pipes
PVCVinyl chloride (chloroethene)Pipes, rain coats, hand bags
PolystyreneStyrene (phenylethene)Insulation, packaging, radio and television cabinets
Teflon (PTFE)TetrafluoroetheneChemically inert; non-stick coatings, oil seals and gaskets
Polyacrylonitrile (PAN)AcrylonitrileSubstitute for wool (orlon, acrilan)

Addition polymer: repeating unit = monomer. Degree of polymerisation = polymer molar mass ÷ monomer molar mass, and mass of polymer = mass of monomer used.

  • LDPE and HDPE both come from ethene: free radical and branched versus Ziegler-Natta and linear.
  • Teflon is from tetrafluoroethene, PAN from acrylonitrile, PVC from vinyl chloride.
  • Element percentages of an addition polymer equal those of its monomer.
  • Total mass is conserved in addition polymerisation.
Read the full lesson

Lesson 3

Condensation polymers: nylons, polyesters and resins

Condensation polymers
PolymerMonomersLink and by-productUses
Nylon 6,6Hexamethylenediamine + adipic acidAmide; waterSheets, bristles for brushes, textiles
Nylon 6Caprolactam (heated with water)Amide; ring openingTyre cords, fabrics, ropes
Terylene (Dacron)Ethylene glycol + terephthalic acidEster; waterFabrics blended with cotton or wool; glass-reinforcing material in safety helmets
GlyptalEthylene glycol + phthalic acidEster; waterPaints and lacquers
BakelitePhenol + methanal (formaldehyde)Methylene bridges; waterCombs, electrical switches, handles of utensils
Melamine-formaldehydeMelamine + methanalWaterUnbreakable crockery

Condensation polymer: repeating unit = sum of monomers − molecules lost (two water molecules for each diamine-diacid or diol-diacid pair). Mass of monomers > mass of polymer.

  • Each monomer needs two reactive groups; three allow cross-linking.
  • Nylon numbers count carbons: nylon 6,6 = C6 diamine + C6 diacid.
  • Terylene and glyptal are both polyesters of ethylene glycol: with terephthalic and phthalic acid respectively.
  • Nylon 6,6 repeat unit 226 g/mol; terylene 192 g/mol.
Read the full lesson

Lesson 4

Copolymers and rubbers: natural, vulcanised and synthetic

Synthetic rubbers
RubberMonomer(s)TypeUses
NeopreneChloroprene (2-chloro-1,3-butadiene)Homopolymer, free radicalConveyor belts, gaskets, hoses
Buna-S1,3-Butadiene + styreneCopolymerAutotyres, floor tiles, footwear, cable insulation
Buna-N1,3-Butadiene + acrylonitrileCopolymerOil seals, tank linings; resists petrol and oils

Natural rubber = cis-1,4-polyisoprene, one C=C per 68 g unit. Vulcanisation = sulphur cross-links. Buna-S: butadiene + styrene; Buna-N: butadiene + acrylonitrile; neoprene: chloroprene.

  • Cis geometry and weak forces make natural rubber elastic.
  • Vulcanisation with sulphur adds cross-links, improving strength and temperature range.
  • Buna-N resists oils because of its polar nitrile groups.
  • For copolymers, compute the mass of one 'set' of units in the given mole ratio.
Read the full lesson

Lesson 5

Molar mass of polymers and biodegradable polymers

Mn = ΣNiMi ÷ ΣNi; Mw = ΣNiMi² ÷ ΣNiMi; PDI = Mw ÷ Mn ≥ 1, equal to 1 only when all chains are the same.

  • Mn counts every chain once; Mw favours heavy chains; Mw ≥ Mn.
  • PDI = 1 means monodisperse, typical of natural polymers such as proteins.
  • PHBV: 3-hydroxybutanoic + 3-hydroxypentanoic acid. Nylon-2-nylon-6: glycine + aminocaproic acid.
  • For equal numbers of chains, use one chain of each to keep arithmetic small.
Read the full lesson

Lesson 6

Reading a repeating unit: from polymer to monomer and back

Reading a repeating unit
What you see in the chainTypeWhere to cut or what to doPieces you get
Only C–C bonds in the backboneAdditionClose up two carbons, restore C=COne alkene (or diene) monomer
–CO–NH– linksCondensation (polyamide)Cut each link, add H2ODiamine + dicarboxylic acid
–CO–O– linksCondensation (polyester)Cut each link, add H2ODiol + dicarboxylic acid
–CH2– bridges joining ringsCondensation (resin)Remove the bridge, restore H on the ringPhenol + methanal

All-carbon backbone: close up two carbons and restore the double bond. Amide or ester links: cut every link and add water back to each half.

  • Read the backbone first: it tells you the type of polymer before you recall any name.
  • For addition polymers the monomer is the repeating unit with a C=C restored; a simple alkene contributes two backbone carbons.
  • For condensation polymers cut each amide or ester link and add H2O; count carbons to get the nylon number or the acid.
  • Always read whether a question asks about the backbone or the whole chain.
Read the full lesson

Lesson 7

Matching polymers to properties, uses and trade names

Polymers, properties and uses
PolymerTrade or common namesKey propertyTypical uses
Polytetrafluoroethene (PTFE)TeflonChemically inert, very low friction, high melting pointNon-stick coatings, gaskets, oil seals
Polyacrylonitrile (PAN)Orlon, AcrilanSoft, warm, wool-like fibreSubstitute for wool, blankets, knitwear
Polyester of ethylene glycol and terephthalic acidTerylene, DacronStrong, crease-resistant fibreFabrics blended with cotton or wool
Poly(methyl methacrylate) (PMMA)Perspex, PlexiglasTransparent, light, shatter-resistantLenses, sign boards, aircraft windows
PolystyreneThermocol when expandedLight, poor conductor of heatPackaging, insulation
Polyvinyl chloride (PVC)PVCTough, flexible when plasticisedPipes, raincoats, cable insulation
Nylon 6,6 and nylon 6NylonStrong fibre, hydrogen bonds between chainsRopes, tyre cords, fabrics, brush bristles
Phenol-formaldehyde resinBakeliteHard, cross-linked, does not soften on heatingSwitches, handles, combs

Do not memorise pairs alone: attach each use to a property that follows from the structure, such as inertness for Teflon, clarity for PMMA, trapped air for foam and cross-linking for Bakelite.

  • Teflon is PTFE; Orlon is polyacrylonitrile; Terylene and Dacron are the same polyester; Perspex is PMMA.
  • Fibres have strong forces between straight chains; thermosets are cross-linked; foams insulate because of trapped air.
  • Plasticisers make PVC flexible by weakening the forces between chains.
  • Addition polymers keep the monomer's formula, so element percentages come from the monomer.
Read the full lesson

Lesson 8

Polymer mass balance: yield, limiting monomer and composition problems

Mass balance
TypeMass of polymerCheck
AdditionEquals the total mass of monomer that reactedNothing is lost
Condensation (diamine + diacid, or diol + diacid)Total monomer mass minus 36 g for every mole of repeating unitEach repeating unit has two links, each losing one H2O of 18 g

Addition: polymer mass = monomer mass. Condensation: polymer mass = monomers minus 18 g of water for each link. Yield applies to the polymer; divide by it to find the monomer needed.

  • Condensation polymer mass = monomer mass − 36 g per mole of repeating unit (diamine-diacid or diol-diacid).
  • The limiting monomer fixes the number of repeating units; the excess is left over.
  • Monomer needed = target polymer mass ÷ fractional yield.
  • Convert copolymer mass percentages to moles before finding the ratio of units.
Read the full lesson

Lesson 9

Mixed polymer problems: identification, elimination and traps

Composition tells you the repeating unit; a test for C=C tells you the saturation; the backbone tells you the type. Use all three clues before you choose an option.

  • An addition polymer has the monomer's percentage composition.
  • Nitrogen percentage separates polyacrylonitrile (26.4%) from nylon 6,6 (12.4%).
  • Several polymers can share an empirical formula, so one number may not be enough.
  • Only polymers with C=C left in the chain, such as natural rubber and Buna-S, decolourise bromine water.
Read the full lesson

Privacy · Terms · Refunds · Delivery