Revision notes

Properties of Matter: Practice

The key points, rules to remember, tables and diagrams from all 9 lessons, on one page for quick revision. To keep a copy, use your browser's Print and choose "Save as PDF".

Lesson 1

Stress, strain and Hooke's law

Y = FL/(AΔL). Stress is proportional to strain only below the elastic limit. Young's modulus depends on the material, not on the size of the wire.

— Remember
  • Stress is force per area; strain is fractional change and has no unit.
  • Extension is proportional to force and length, inversely proportional to area.
  • Always convert mm² to m² before substituting.
Read the full lesson

Lesson 2

Elastic behaviour and energy stored in a wire

Elastic energy U = ½ F ΔL = ½ kx². Energy per unit volume = ½ × stress × strain. Beyond the elastic limit deformation is permanent.

— Remember
  • Past the elastic limit the body does not return to its original size.
  • Stored energy is the area under the force-extension graph, ½ F ΔL.
  • Energy per volume equals ½ × stress × strain.
Read the full lesson

Lesson 3

Surface tension and excess pressure

Drop: ΔP = 2T/r. Soap bubble: ΔP = 4T/r. Smaller bubbles have higher internal pressure. A soap film has two surfaces.

— Remember
  • Surface tension is force per length, and equals surface energy per area.
  • Count the number of surfaces: drop has one, soap bubble has two.
  • Excess pressure is greater in smaller drops and bubbles.
Read the full lesson

Lesson 4

Capillarity and angle of contact

h = 2T cos θ/(rρg). θ < 90° rise; θ > 90° fall. h is proportional to 1/r. The rise does not depend on the tube's length (above the level reached).

— Remember
  • Capillary rise is inversely proportional to the tube radius.
  • A wetting liquid rises; a non-wetting liquid is depressed.
  • Use SI units: radius in metres, T in N/m.
Read the full lesson

Lesson 5

Viscosity and terminal velocity

Stokes' drag F = 6πηrv. Terminal velocity v_t = 2r²(ρ − σ)g/9η is proportional to r². At v_t, net force is zero. Liquids get less viscous when heated.

— Remember
  • Terminal velocity occurs when drag plus buoyancy equals weight.
  • v_t depends on r², density difference and 1/η.
  • Liquids become less viscous with heat; gases become more viscous.
Read the full lesson

Lesson 6

Bulk modulus, shear modulus and Poisson's ratio: problem types

ΔV ÷ V = ΔP ÷ K. Shear: θ = x ÷ h and G = (F ÷ A) ÷ θ. Radius changes by one-third of the fractional volume change.

— Rule to remember
  • Bulk: find the fractional change first, then multiply by the volume.
  • Shear: stress, then strain as an angle, then displacement x = θh.
  • Poisson: lateral strain is σ times longitudinal strain.
Read the full lesson

Lesson 7

Wires and springs: ratio shortcuts, cutting springs and load sharing

Wire: ΔL ∝ L ÷ (r²Y). Spring piece of fraction f: k ÷ f. Series: reciprocals add. Parallel: constants add.

— Rule to remember
  • Write the dependence first, then put in the ratios.
  • Shorter spring means stiffer spring.
  • Equal extension means load is shared in proportion to stiffness.
Read the full lesson

Lesson 8

Surface tension forces and work: frames, rings, needles and bubbles in liquid

Force = T × length of contact line. Soap film: two surfaces, so 2Tl. Work = T × increase in area. Air bubble in liquid: 2T ÷ r.

— Rule to remember
  • Count the contact line and the number of surfaces before using the formula.
  • Work equals surface tension times the new area.
  • Gauge pressure of a bubble in water adds hρg to 2T ÷ r.
Read the full lesson

Lesson 9

Mixed problem set: capillary rise, merging drops, Stokes and Poiseuille by ratios

How each quantity depends on size
QuantityDepends onPattern
Capillary rise h1/r (and T cosθ ÷ ρ)Narrower tube, higher rise
Excess pressure in drop or bubble1/RSmaller drop, higher pressure
Terminal velocity vₜr² (ρ − σ) ÷ ηLarger drop, much faster
Poiseuille flow QP r⁴ ÷ (η l)Radius has the biggest effect
Wire extension ΔLF L ÷ (r² Y)Thicker wire, smaller stretch
Merging n dropsR = n^(1/3) rVolume is conserved

Write the dependence, plug the ratios, cancel the constants. Capillary h ∝ 1/r. Terminal speed ∝ r². Flow ∝ r⁴.

— Rule to remember
  • Learn the dependence of each quantity.
  • Substitute ratios, not actual values, to save time.
  • Check which factors stay constant before cancelling.
Read the full lesson

Privacy · Terms · Refunds · Delivery