• Practice
  • About 14 min
  • 5 practice questions

Capillarity and angle of contact

Find the height of capillary rise or fall using h = 2T cos θ/(rρg) and understand wetting.

If something looks wrong, please tell us.

Water climbs up a narrow glass tube, and mercury is pushed down in the same tube. This is capillarity, and it is the reason that plants draw water and a blotting paper soaks ink. The angle of contact decides which way the liquid goes.

Angle of contact

The angle of contact θ is the angle between the liquid surface and the solid, measured through the liquid. If θ is less than 90° (water on clean glass), the liquid wets the surface, its meniscus is concave and it rises in a capillary tube. If θ is greater than 90° (mercury on glass), the meniscus is convex and the liquid is depressed.

Capillary rise

For a tube of radius r dipped in a liquid of surface tension T and density ρ: h = 2T cos θ / (r ρ g). The rise is inversely proportional to the radius: a thinner tube raises the liquid higher.

Worked examples (g = 10 m/s²)

Example 1. Water (T = 0.07 N/m, ρ = 1000 kg/m³, θ = 0°) in a tube of radius 0.5 mm = 5 × 10⁻⁴ m: h = 2 × 0.07/(5 × 10⁻⁴ × 1000 × 10) = 0.14/5 = 0.028 m = 2.8 cm.

Example 2. If the radius of the tube is halved, h doubles: 5.6 cm.

Example 3. Two capillary tubes of radii 1 mm and 2 mm are dipped in water. The ratio of heights h₁ : h₂ = 1/1 : 1/2 = 2 : 1.

Example 4. For mercury, the angle of contact is more than 90°, so cos θ is negative and h is negative: the mercury surface inside the tube is below the outside level.

h = 2T cos θ/(rρg). θ < 90° rise; θ > 90° fall. h is proportional to 1/r. The rise does not depend on the tube's length (above the level reached).

— Remember

Key takeaways

  • Capillary rise is inversely proportional to the tube radius.
  • A wetting liquid rises; a non-wetting liquid is depressed.
  • Use SI units: radius in metres, T in N/m.

Check your understanding

  1. 1. A liquid has an angle of contact less than 90° with glass. In a glass capillary tube its meniscus is:

    1. Concave, and the liquid rises
    2. Convex, and the liquid rises
    3. Concave, and the liquid is depressed
    4. Convex, and the liquid is depressed
    Show answer

    Answer: A. θ < 90° (like water on clean glass) means the liquid wets the glass: concave meniscus and capillary rise. θ > 90° (mercury) gives a convex meniscus and depression.

  2. 2. Water (T = 0.07 N/m, ρ = 1000 kg/m³, θ = 0°) is in a capillary tube of radius 0.5 mm. Taking g = 10 m/s², how high does it rise?

    1. 1.4 cm
    2. 5.6 cm
    3. 2.8 cm
    4. 28 cm
    Show answer

    Answer: C. h = 2T cos θ ÷ (rρg) = 2 × 0.07 × 1 ÷ (5 × 10⁻⁴ × 1000 × 10) = 0.14 ÷ 5 = 0.028 m = 2.8 cm.

  3. 3. Water rises to a height h in a capillary tube. If the radius of the tube is doubled, the new height is:

    1. 2h
    2. h/4
    3. 4h
    4. h/2
    Show answer

    Answer: D. h = 2T cos θ ÷ (rρg), so h ∝ 1/r. Doubling r halves the height.

  4. 4. Two capillary tubes of radii 1 mm and 2 mm are dipped in the same water. What is the ratio of the heights h₁ : h₂?

    1. 2 : 1
    2. 1 : 2
    3. 1 : 4
    4. 4 : 1
    Show answer

    Answer: A. h ∝ 1/r, so h₁ : h₂ = 1/1 : 1/2 = 2 : 1.

  5. 5. A capillary tube in which water has risen is tilted. What happens?

    1. The vertical height of the water increases
    2. The vertical height of the water stays the same, and the length of water in the tube increases
    3. The vertical height decreases while the length of water in the tube stays the same
    4. The water flows out of the top of the tube
    Show answer

    Answer: B. Capillary rise fixes the vertical height h. When the tube is tilted, the liquid fills a longer length of tube to reach the same vertical height.

Sign in to keep track of the lessons you finish.

Next lesson → Viscosity and terminal velocity

Privacy · Terms · Refunds · Delivery