Revision notes

Water Chemistry: Practice

The key points, rules to remember, tables and diagrams from all 9 lessons, on one page for quick revision. To keep a copy, use your browser's Print and choose "Save as PDF".

Lesson 1

Expressing hardness: CaCO3 equivalents and units

Conversion factors to CaCO3 equivalents
SaltMolar massFactor (100 ÷ M)Type of hardness
Ca(HCO3)21620.617Temporary
Mg(HCO3)21460.685Temporary
CaSO41360.735Permanent
MgSO41200.833Permanent
CaCl21110.901Permanent
MgCl2951.053Permanent
Mg(NO3)21480.676Permanent

Hardness as CaCO3 = mass of salt × 100 ÷ molar mass of salt. 1 ppm = 1 mg/L = 0.1 °Fr = 0.07 °Cl. Sodium and potassium salts never count.

— Rule to remember

Convert every calcium and magnesium salt to CaCO3 equivalents before adding. Keep the factor table in memory, scale every mass to one litre, and ignore sodium and potassium salts. Unit conversions are simple multipliers: divide ppm by 10 for degrees French and multiply by 0.07 for degrees Clarke.

Read the full lesson

Lesson 2

Temporary, permanent and total hardness problems

Worked example 1 laid out
Saltmg/LTypeAs CaCO3 (ppm)
Ca(HCO3)281T50
Mg(HCO3)273T50
CaSO4136P100
MgCl295P100
NaCl50X0

Sort (T, P or X), convert each to CaCO3 with × 100 ÷ M, then add. Total = temporary + permanent. For a tank, ppm × litres = mg.

— Rule to remember

A three-step routine solves almost every hardness question: sort, convert, add. Work backwards with mass = hardness × M ÷ 100. When the hardness is already given as CaCO3, the mass of carbonate scale from boiling is the same number, scaled by the volume. Keep sodium salts and sodium hydrogencarbonate out of the sum.

Read the full lesson

Lesson 3

Softening methods: lime-soda, zeolite and ion-exchange resins

Comparing softening methods
MethodRemovesLeft in the waterRegenerated with
Lime-sodaCa and Mg hardnessSome residual hardness, sodium saltsNot regenerated (chemicals consumed)
ZeoliteCa2+ and Mg2+Sodium salts of the original anionsBrine (NaCl)
Ion-exchange resinsAll cations and anionsAlmost nothingAcid (cation) and alkali (anion)

Lime: 1 for temporary Ca, 2 for temporary Mg, 1 for permanent Mg. Soda: 1 for permanent Ca and 1 for permanent Mg. Zeolite swaps cations only; resins in H+ and OH− forms remove all ions.

— Rule to remember

Write the lime-soda reactions until the counts are automatic, since they are the calculation formula in disguise. Zeolite softens but leaves sodium salts and is regenerated with brine. Cation plus anion resins give demineralised water and are regenerated with acid and alkali.

Read the full lesson

Lesson 4

Lime-soda and zeolite calculations

Speed factors
QuantityMultiply CaCO3 equivalent by
Lime, Ca(OH)274/100
Soda, Na2CO3106/100
Salt for zeolite, NaCl117/100
Back to a salt such as MgSO4M/100

Lime = 0.74 × [temp Ca + 2 temp Mg + perm Mg] × V. Soda = 1.06 × [perm Ca + perm Mg] × V. Zeolite salt = 1.17 × (ppm × V). All hardness as CaCO3; answers in mg.

— Rule to remember

Lime-soda problems are two brackets and two factors. Zeolite problems are one factor, 117/100, in either direction. Convert salts to CaCO3 first, multiply by the volume, convert milligrams to kilograms at the end, and divide by purity if the chemical is not pure.

Read the full lesson

Lesson 5

EDTA titration, dissolved oxygen and BOD calculations

Formulae for this lesson
QuantityFormula
Hardness by EDTAmL EDTA × M × 100 × 1000 ÷ mL sample (ppm as CaCO3)
Temporary hardnessTotal − permanent (after boiling)
Dilution factorTotal volume ÷ sample volume
BOD(DO start − DO end) × dilution factor

Hardness (ppm) = V(EDTA) × M × 100 × 1000 ÷ V(sample). EBT turns wine red to blue at pH 10. BOD = DO drop × (total volume ÷ sample volume).

— Rule to remember

EDTA titration gives total hardness; titrating a boiled sample gives permanent hardness, and the difference is temporary. The formula carries a factor of 100 for CaCO3 and 1000 for per litre. BOD is a DO difference multiplied by the dilution factor, so always check how far the sample was diluted.

Read the full lesson

Lesson 6

Hardness of blended waters, daily loads and partial softening

Hardness adds as mass: H × V. Mixture = total mass ÷ total volume. For a target, solve H = xH1 + (1 − x)H2. Dilution halves the hardness of each water when equal volumes are mixed.

  • Weight each hardness by its volume; never average ppm values of unequal volumes.
  • Check that a blended answer lies between the two sources.
  • Daily load = ppm × litres, divided by 10^6 for kg.
  • Blending softened and raw water reduces the amount of salt or chemicals needed.
Read the full lesson

Lesson 7

Lime-soda in practice: impure chemicals, daily requirement and cost

Counts per unit of hardness (as CaCO3)
Type of hardnessLime factorSoda factor
Temporary calcium10
Temporary magnesium20
Permanent calcium01
Permanent magnesium11

Pure lime = 0.74 × [Ca-T + 2Mg-T + Mg-P]; pure soda = 1.06 × [Ca-P + Mg-P]. Impure mass = pure mass ÷ purity. Cost = mass in kg × price per kg.

  • Fill the two brackets before multiplying by the factor and the volume.
  • Divide by the purity fraction; an impure chemical always weighs more than the pure requirement.
  • Convert mg to kg by dividing by 10^6.
  • Permanent magnesium needs both lime and soda.
Read the full lesson

Lesson 8

Alkalinity problems: phenolphthalein and methyl orange titrations made simple

Alkalinity table (all as ppm CaCO3)
ResultOH−CO3 2−HCO3−
P = 000M
P < M/202PM − 2P
P = M/202P0
P > M/22P − M2(M − P)0
P = MM00

Compare P with M/2. P = 0: only HCO3−. P < M/2: CO3 2− = 2P, HCO3− = M − 2P. P > M/2: OH− = 2P − M, CO3 2− = 2(M − P). Carbonate hardness = the smaller of alkalinity and total hardness.

  • P and M come from the two end points; both are expressed as ppm of CaCO3.
  • OH− and HCO3− never occur together.
  • The components must add up to M; use this as a check.
  • Carbonate hardness is limited by the smaller of alkalinity and total hardness.
Read the full lesson

Lesson 9

Mixed water-chemistry problem set: from analysis to treatment

Sort, convert, add; fill the brackets; scale by volume; divide by purity. Check with an independent route (EDTA volume or BOD below COD) whenever the data allow.

  • Work in a fixed order: convert, sort, add, treat, scale, correct for purity.
  • The same hardness figure feeds lime-soda, zeolite and EDTA calculations.
  • BOD cannot be larger than COD; their ratio shows biodegradability.
  • Check units at the start and the size of the answer at the end.
Read the full lesson

Privacy · Terms · Refunds · Delivery