- Practice
- About 16 min
- 5 practice questions
Wind calculations: ratios, rotor size and the power coefficient
Solve wind power questions quickly with ratio methods, compute power from rotor diameter, and apply the power coefficient and Betz limit correctly.
If something looks wrong, please tell us.
Wind power questions reward one habit above all: work with ratios. Because the power in the wind is ½ρAv³, most questions about change can be answered without ever plugging in the full formula. When a full calculation is needed, the usual traps are using radius where diameter is given, forgetting to cube, and treating the Betz limit as a real efficiency. This lesson drills each of these.
Ratio method for speed changes
If only the wind speed changes, new power ÷ old power = (new speed ÷ old speed)³. A 20% rise in speed means a speed ratio of 1.2, so power rises by a factor of 1.2³ = 1.728, an increase of 72.8%. A 10% fall in speed gives 0.9³ = 0.729, a fall of about 27%. A small change in wind speed causes a large change in power, which is why careful site measurement matters so much.
Power ratio = (speed ratio)³ × (area ratio) × (density ratio). Area ratio = (radius ratio)² = (diameter ratio)².
Rotor size
The swept area is a circle, A = πr². If a question gives the rotor diameter, halve it first to get the radius. A 40 m diameter rotor has r = 20 m and A = π × 400 ≈ 1,257 m². Doubling the diameter quadruples the area; tripling it makes the area nine times as large. Air density matters too, but only in proportion: colder, denser air carries a little more power, and thin air at high altitude a little less.
Power coefficient and the Betz limit
The fraction of the wind's power that a turbine actually captures is its power coefficient, Cp. The Betz limit says Cp can never exceed 16/27, about 0.593. Real turbines reach lower values, and the electrical output is lower still after gearbox and generator losses. So there are three levels: power in the wind, the Betz maximum, and what the machine actually delivers. Read the question to see which is wanted.
Operating speeds
A turbine starts generating at its cut-in speed, when the wind is just strong enough to turn it usefully. Output then climbs steeply, following the cube rule, until the rated speed, where the turbine reaches its rated power. Above that, the blades are turned to spill extra wind so output stays at rated power. At the cut-out speed, in a storm, the turbine stops to protect itself. A question that asks why output does not keep rising with the cube of speed in strong wind is testing this idea.
Worked example 1: a 40 m rotor
A turbine has a rotor diameter of 40 m. Wind speed is 8 m/s and air density 1.2 kg/m³. Radius = 20 m, A = π × 20² ≈ 1,256.6 m². v³ = 8 × 8 × 8 = 512. Power in the wind = ½ × 1.2 × 1,256.6 × 512 ≈ 0.6 × 643,380 ≈ 386,000 W ≈ 386 kW. If Cp = 0.40, the turbine captures 0.40 × 386 ≈ 154 kW. The Betz maximum would be 0.593 × 386 ≈ 229 kW.
Worked example 2: two changes at once
A turbine is replaced by one with blades 1.5 times as long, and is moved to a site where the wind is 20% faster. Area ratio = 1.5² = 2.25. Speed ratio cubed = 1.2³ = 1.728. Power ratio = 2.25 × 1.728 = 3.888. So the new turbine has about 3.9 times the power in the wind. Multiply the separate ratios; never add the percentage changes.
Worked example 3: the speed for a target
At 6 m/s a turbine produces 100 kW. Ignoring the rated-speed cap, what speed gives 800 kW? The power ratio is 8, so the speed ratio is the cube root of 8, which is 2. New speed = 6 × 2 = 12 m/s. When the target ratio is a perfect cube (8, 27, 64), this is quick.
Key takeaways
Use ratios: power changes with the cube of speed, the square of radius or diameter, and in proportion to density. Halve a diameter before squaring. Distinguish power in the wind, the Betz maximum of about 59.3%, and the actual output given by Cp. Above rated speed, output is held constant; at cut-out the turbine stops.
Check your understanding
-
1. Wind speed at a turbine falls by 10%. By roughly what percentage does the power in the wind fall?
- 10%
- 30%
- About 27%
- About 19%
Show answer
Answer: C. Speed ratio 0.9; power ratio 0.9³ = 0.729, a fall of about 27.1%. Tripling the percentage gives the wrong 30%.
-
2. A rotor's diameter increases from 60 m to 90 m, with wind unchanged. The power in the wind through the rotor becomes:
- 2.25 times as large
- 1.5 times as large
- 3.375 times as large
- 4 times as large
Show answer
Answer: A. Diameter ratio 1.5; area ratio 1.5² = 2.25. Power is proportional to area.
-
3. The power in the wind through a rotor is 500 kW and the turbine's power coefficient is 0.35. What power does the rotor capture?
- 296.5 kW
- 500 kW
- 142 kW
- 175 kW
Show answer
Answer: D. Captured power = Cp × power in wind = 0.35 × 500 = 175 kW. (296.5 kW would be the Betz maximum.)
-
4. Why does a turbine's output stop rising with the cube of wind speed above its rated speed?
- The blades are adjusted to spill wind and hold output at rated power
- The Betz limit falls in strong wind
- Air density becomes zero at high speed
- The generator switches to direct current
Show answer
Answer: A. Above rated speed, the control system turns the blades to limit the captured power to the rated value, protecting the machine.
-
5. At 5 m/s a turbine produces 40 kW. Ignoring the rated cap, what power does it produce at 15 m/s?
- 1,080 kW
- 120 kW
- 360 kW
- 1,000 kW
Show answer
Answer: A. Speed ratio 3; power ratio 3³ = 27. 40 × 27 = 1,080 kW.
Sign in to keep track of the lessons you finish.